Bowflex BXT116 Скачать руководство пользователя страница 146

Страница: 146 / 179

146

14. Connect the Input/Output (I/O) and Grounding Cables and attach the

new Right Upright to Frame Assembly

Note:

This step may take two people to safely hold the Right Upright while

the Cables are connected. Do not crimp the Cables. Do not fully tighten

the Hardware until the Console and Handlebar Assembly has been at-

tached.

15. Re-install all remaining parts that were removed in reverse order.

16. Final Inspection

Inspect your machine to ensure that all hardware is tight and components

are properly assembled.

Do not use until the machine has been fully assembled and

inspected for correct performance in accordance with the

Owner’s Manual.

6mm

13. Using a 6mm hex wrench, remove the hardware from the Right Up

right. Slightly remove the Right Upright from the Base Assembly exposing

the Input/Output (I/O) and Grounding Cables. Disconnect the Cables and

remove the Right Upright.

Note:

Do not crimp cables.

Содержание BXT116




















































































































































































Результаты поиска

Содержание BXT116

Отзывы:

Бренды по названию

Популярные бренды

Bowflex BXT116, Руководство по обслуживанию

Результаты поиска

Содержание BXT116

Отзывы:

Бренды по названию

Популярные бренды