Bowflex BXT116 Скачать руководство пользователя

Страница: 104 / 179

104

1. Unplug the power cord from the machine and wait 5 minutes. Place the

power cord in a secure location.

2. Using a standard screwdriver, gently lift and release the Junction Cover

End Caps from the Console Assembly.

3. Remove the Junction Cover End Caps from the Console Assembly.

4. Using a #2 Phillips screwdriver, remove the 4 indicated screws (by ar-

rows) from Lower Junction Covers.

5. Gently release the snaps (indicated by ovals, two on each side) that

secure the Upper and Lower Junction Covers and remove the Upper

Junction Covers.

6. Gently pull out the Input/Output (I/O) and Grounding Cables from the

Right Upright, and disconnect them. Do not allow the Cables to fall into

the Right Upright. Secure them with A Zip-Tie, rubber band or piece of

wire.

Note:

Do not crimp the Cables.

To reduce the risk of electrical shock or unsupervised usage of the equipment, always unplug the power cord from the

wall outlet and wait 5 minutes before cleaning, maintaining or repairing this machine. Place the power cord in a secure

location.

Console

Assembly

Junction Cover End Caps

Lower Junction

Covers

Содержание BXT116




















































































































































































Результаты поиска

Содержание BXT116

Отзывы:

Похожие инструкции для BXT116

Бренды по названию

Популярные бренды

Bowflex BXT116, Руководство по обслуживанию

Результаты поиска

Содержание BXT116

Отзывы:

Похожие инструкции для BXT116

Бренды по названию

Популярные бренды