Bowflex BXT116 Скачать руководство пользователя

Страница: 159 / 179

159

11. Attach the new Speed Sensor Connector to the Motor Control Board.

12. Route the new Speed Sensor Cable along the Frame.

13. Using replacement Zip-Ties, secure the Speed Sensor Cable to the Frame and trim the excess from the Zip-Ties. Be sure not to cut the Speed

Sensor Cable.

14. Using a #2 Phillips screwdriver, attach the new Speed Sensor

15. Re-install all remaining parts that were removed in reverse order.

16. Final Inspection

Inspect your machine to ensure that all hardware is tight and components are properly assembled.

Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner’s

Manual.

Содержание BXT116




















































































































































































Результаты поиска

Содержание BXT116

Отзывы:

Похожие инструкции для BXT116

Бренды по названию

Популярные бренды

Bowflex BXT116, Руководство по обслуживанию

Результаты поиска

Содержание BXT116

Отзывы:

Похожие инструкции для BXT116

Бренды по названию

Популярные бренды