Bowflex BXT116 Скачать руководство пользователя

Страница: 122 / 179

122

6. Gently release the front snaps (indicated by ovals) that secure the

Motor Cover and pivot it back toward the walking belt until it releases.

Remove from the machine.

7. Using a #2 Phillips screwdriver, remove the 2 indicated screws from

the Motor Control Board Cover. Lift and remove the Motor Control Board

Cover.

8. Re-install the parts that were removed in reverse order.

9. Final Inspection

Inspect your machine to ensure that all hardware is tight and components

are properly assembled.

Do not use until the machine has been fully assembled and

inspected for correct performance in accordance with the

Owner’s Manual.

Motor Control Board Cover

Содержание BXT116




















































































































































































Результаты поиска

Содержание BXT116

Отзывы:

Похожие инструкции для BXT116

Бренды по названию

Популярные бренды

Bowflex BXT116, Руководство по обслуживанию

Результаты поиска

Содержание BXT116

Отзывы:

Похожие инструкции для BXT116

Бренды по названию

Популярные бренды