manualshive.com logo in svg

Bowflex BXT116, Руководство по обслуживанию

Поделиться
Скачать
Bowflex BXT116 Скачать руководство пользователя страница 42

42

5. Make sure that there is safe clearance around, above, and to one side 

of the treadmill. Tilt the machine onto the side being sure not to grasp the 

Console. 

A second person is required to assist with the tilting of the 

machine. Do not tilt the machine unless the walking deck is in 

the folded, locked position. Be sure there is adequate clear-

ance for the raised deck. Some components of the equipment 

can be heavy or awkward. Enlist the service of a second 

person when you do maintenance steps involving these 

components. Do not try to do heavy or awkward steps on your 

own. 

!

The following images show the machine upright, 

and not fully resting on its side. The machine must 

be on its side to safely complete the following 

steps.

Lift Shock

Deck Release Handle

6. Using a 14mm wrench, disconnect the securing nut (indicated by oval) 

and remove the hardware from the Lift Shock.

Содержание BXT116




















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды