Bowflex BXT116 Скачать руководство пользователя

Страница: 22 / 179

Incline Issues

Contact

Tech Support at

800.861.7401

for further assistance.

Issue resolved

Is the issue still

present?

YES

Follow Service Mode

Procedure 1 to test

Console communication.

Does Incline Motor

move?

Does Incline

Motor make any grinding/-

clunking noises or move

without the rails inclining? Be

patient as the Motor

moves slowly.

Replace Incline Motor

Refer to “Replace the

Incline Motor” procedure

in the Service Manual and

reseat all cable connec-

tions.

Follow Service Mode

Procedure 2 to check

firmware version and error

codes.

BEGIN HERE

Is the issue still

present?

YES

Did the

communications

test pass?

Reset machine power and

follow Service Mode

Procedure 4 to calibrate

the MCB.

YES

Follow Service Mode

Procedure 5 to test the

incline buttons.

Replace I/O cables

Did the incline

buttons pass the

test?

Replace Console

YES

Follow Service Mode

Procedure 5 to test the

incline buttons.

Replace Incline Motor

Did the incline

buttons pass the

test?

Replace Console

Содержание BXT116




















































































































































































Результаты поиска

Содержание BXT116

Отзывы:

Похожие инструкции для BXT116

Бренды по названию

Популярные бренды

Bowflex BXT116, Руководство по обслуживанию

Результаты поиска

Содержание BXT116

Отзывы:

Похожие инструкции для BXT116

Бренды по названию

Популярные бренды