Bowflex BXT116 Скачать руководство пользователя

Страница: 129 / 179

129

11. Attach the new Motor Mount to the Motor. Be sure the Belt Tensioner

Screw is properly oriented toward the rear of the machine when the Motor is

re-installed.

12. Lightly attach the Motor Assembly to the Frame. Be sure to only finger

tighten the hardware.

13. Loop the Drive Belt onto the Motor Pulley. With the Drive Belt looped onto

the Motor, carefully roll the Drive Belt onto the Drive Pulley in a clockwise mo-

tion. Be sure the Belt does not come off of the Motor Pulley.

Keep fingers out of any pinch opportunities when turning the

Pulleys.

14. Roll the Drive Pulley clockwise until the Drive Belt is fully installed. Con-

tinue to roll the Belt forward while adding side pressure with fingers to align as

necessary.

15. With the Motor Assembly loosely attached to the Frame, turn the Belt

Tensioner Screw to the previous level. This will tighten the Drive Belt to the

previous tension level.

16. Using a 6mm hex wrench, fully tighten the screws that attach the Motor

Assembly to the Frame.

17. Re-install all remaining parts that were removed in reverse order.

18. Attach the power cord and turn on the Treadmill by flipping the power

switch to ON.

19. From the Power Up (or Welcome) screen, push and hold down the

PAUSE/STOP button and Down arrow button for about 5 seconds to go into

the Machine Setting Mode. The Console display will show the TOTAL HOURS

screen.

Motor

Drive Belt

Belt Tensioner Screw

Motor Mount

Содержание BXT116




















































































































































































Результаты поиска

Содержание BXT116

Отзывы:

Похожие инструкции для BXT116

Бренды по названию

Популярные бренды

Bowflex BXT116, Руководство по обслуживанию

Результаты поиска

Содержание BXT116

Отзывы:

Похожие инструкции для BXT116

Бренды по названию

Популярные бренды