Bowflex BXT116 Скачать руководство пользователя

Страница: 124 / 179

124

1. With power supplied to the machine and it turned on, adjust the Walking

Deck Incline to a setting of ‘6’. To adjust, push the ‘6’ Pre-Set Incline but-

ton, and then the Confirm Incline button. Allow the Walking Deck to adjust

to the new incline height.

2. Unplug the power cord from the machine and wait 5 minutes. Place the

power cord in a secure location.

To reduce the risk of electrical shock or unsu-

pervised usage of the equipment, always unplug

the power cord from the wall outlet and wait 5

minutes before cleaning, maintaining or repair-

ing this machine. Place the power cord in a

secure location.

3. Using a #2 Phillips screwdriver, remove the screw (indicated by ovals)

from each of the Base Shrouds.

4. Remove the Base Shrouds from the machine.

5. Using a #2 Phillips screwdriver, remove the 10 indicated screws that

secure the Motor Cover.

Note:

There are 2 screws that secure the Motor Cover from the underside

of the machine (see image to the right).

Note:

The Bowflex

BXT116 is used in the following images. The procedure is the same for the BXT216 model.

(on each side of the Motor

Cover)

Right Base Shroud

Left Base

Shroud

Motor Cover

Содержание BXT116




















































































































































































Результаты поиска

Содержание BXT116

Отзывы:

Похожие инструкции для BXT116

Бренды по названию

Популярные бренды

Bowflex BXT116, Руководство по обслуживанию

Результаты поиска

Содержание BXT116

Отзывы:

Похожие инструкции для BXT116

Бренды по названию

Популярные бренды