Bosch Rexroth IndraControl S20 страница 28 Скачать руководство пользователя

Страница: 28 / 88

Fig. 5-4:

Removing electronics module

Remove all connectors before removing the module.
Use a suitable tool (e.g. slotted screwdriver) and put it first into the upper and

then into the lower disengaging mechanism (base latch) of the module to dis‐

engage it (A).
Remove the module vertically to the mounting rail (B).

Attaching and removing plugs

Fig. 5-5:

Attaching plug

Set the plug vertically to its position. The plugs are color-coded, but not hard‐

ware-coded. Observe the colored markings of the plugs or slots. Assignment

from left to right: blue, red, white, green.
Press the plug down until it is fix. Ensure that the locking clip engages.

Fig. 5-6:

Removing plug

Disengaging the locking clips (A).
Tilt the plug a bit up (B).
Remove the plug from the module (C).

Bosch Rexroth AG

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

26/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

Mounting, demounting and electric installation

Содержание Rexroth IndraControl S20

























































































Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl S20, Руководство пользователя

Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды