Bosch Rexroth IndraControl S20 Скачать руководство пользователя

Страница: 19 / 88

Name

Color

State

Description

CSos module status
Off

Red/green flash‐

ing

Self test or configuration is active or required.

Green flashing

Module is in "Stop" state. The outputs are "0".

Green on

GN GN

The outputs are valid.

Flashing red

Recoverable error. Recoverable errors are for example configuration errors of

the Csos firmware.

Red on

RD RD

Unrecoverable error. It is possible that the module has to be replaced.

CSos safety network status
Off

Module has no connection to the originator

Green flashing

The connection to the originator is established, but no I/O data is exchanged.

Green on

GN GN

I/O data is exchanged with the originator.

Flashing red

I/O connection to originator failed.

Red on

RD RD

An error was detected in the connection that does not allow further process‐

ing.

Red/green flash‐

ing

The module is ready to set a new TUNID via DIP switches. The new TUNID is

applied upon the next voltage startup.

00-07

Status per output 0-7
Off

Output, logic "0".

Green on

GN GN

Output, logic "1".

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

Bosch Rexroth AG

17/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

Product description

Содержание Rexroth IndraControl S20

























































































Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl S20, Руководство пользователя

Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды