Bosch Rexroth IndraControl S20 Скачать руководство пользователя

Страница: 39 / 88

Error type

Identifi‐

cation

Diagnos‐

tics

Loss of
SF

Notes

Error in actuator
Even though it was witched off, the

actuator does not go into the safe

state (e.g. not opening a contact)

None

Yes

Install an error detection by external monitoring. Ob‐

serve all errors that can occur in the actuator.
Test the switch-off capability of the actuator in rea‐

sonable intervals.
Use a dual-channel actuator if required.

Actuator cannot be switched on

(e.g. interruption)

None

Install an error detection by external monitoring. Ob‐

serve all errors that can occur in the actuator.
Ensure that this error does not cause a delayed sys‐

tem startup.

More errors (depending on the ac‐

tuator)

Consider all errors that can occur in the actuator.

Error in wiring
Interruption
Interrupting the wire between out‐

put and actuator or between actua‐

tor and ground

None

Install an error detection by external monitoring. Ob‐

serve all errors that can occur in the actuator.
Ensure that this error does not cause a delayed sys‐

tem startup.

Cross-fault
Output against output

Yes

All LEDs

OUT: Red

Yes

Cross-fault between the outputs is only detected

when the outputs are in a switched-off state if the

test pulses are switched on. If an error is detected,

the module disables all its outputs.

Short circuit
Output against ground or output

against FE

Yes

Short cir‐

cuit or

overload,
OUTx

The error is detected in enabled state. The output is

disabled (safe state). It can only be switched on

again at a rising edge from "0" to "1" after trouble‐

shooting and acknowledgement.
WARNING!
Unexpected machine startup due to an "Operator Ac‐

knowledgement"
Note that an "Operator Acknowledgement" can

cause the outputs to be switched on again.

SF = Safety function

OUTx = Diagnostic message (LED) per output X

Tab. 7-3:

Single-channel: Test pulses switched on

Exemplary parameterization

Parameterization

Parameterized as

Notes

Assignment

Assigned

Output

Single-channel

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

Bosch Rexroth AG

37/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

Connection examples of the safe outputs

Содержание Rexroth IndraControl S20

























































































Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl S20, Руководство пользователя

Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды