manualshive.com logo in svg

Bosch Rexroth IndraControl S20, Руководство пользователя

Поделиться
Скачать
Bosch Rexroth IndraControl S20 Скачать руководство пользователя страница 51

Code

Error cause

LED

Description, effect

Acknowledgement, remedy

0x8F09 Dark test error at the

displayed output

All

OUT

red on

Due to the test pulses (short-term switch-

off), an error was detected at the dis‐

played output. All outputs are thus re‐

tained in the safe state.

Read out channel number via the

DiagStateChannelNo object 0x033.
This diagnostic message can be

acknowledged. The acknowledge‐

ment deletes the message and en‐

ables the outputs.
Multiple acknowledgement can be

required for the error.

0x2380 Hardware or cross-

fault errors

All

OUT

red on

The displayed output cannot be disabled.

All outputs are thus retained in the safe

state.

Read out channel number via the

DiagStateChannelNo object 0x033.
This diagnostic message can be

acknowledged. The acknowledge‐

ment deletes the message and en‐

ables the outputs.

0x5010 Hardware error

-

Due to the internal self test mechanism, a

hardware error was detected at the out‐

puts. All outputs are thus retained in the

safe state.

This diagnostic message can be

acknowledged. The acknowledge‐

ment deletes the diagnostic mes‐

sage.
It can only be restarted after an

error-free power-up self test.
If the power-up self test results in

errors, the module has to be re‐

placed.

Tab. 9-9:

Errors of the safe digital outputs

9.2.3 

Errors of the supply voltage

Code

Error cause

LED

Description, effect

Acknowledgement, remedy

0x3411 Undervoltage U

O

 sup‐

ply

UI

flash‐

ing

Undervoltage was detected at the U

O

supply. A diagnostic message is gener‐

ated if U

O

 < 17 V.

All outputs of the module are retained in

the safe state.
The U

O

 LED is permanently on again, as

soon as no undervoltage is detected.

Check and correct the supply volt‐

age.
Check length and load of the sup‐

ply lines.
This diagnostic message can be

acknowledged. The acknowledge‐

ment deletes the message and en‐

ables the outputs.

Tab. 9-10:

Supply voltage error

9.2.4 

Parameterization errors

Parameterization errors cause diagnostic messages of priority 1 in the Dia‐

gState object. These errors cannot be acknowledged: The parameterization

has to be checked and corrected.
To identify the type of parameterization error, go online with IndraWorks on

the control and read out the error.

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P 

Bosch Rexroth AG

49/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

Errors: Reporting and troubleshooting

Содержание Rexroth IndraControl S20

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды