Bosch Rexroth IndraControl S20 Скачать руководство пользователя

Страница: 62 / 88

①

Loss of the safety function

due to the use of unsuitable

voltage supplies

WARNING

For the voltage supply at the bus coupler, use only voltage

supplies acc. to EN 50178/VDE 0160 (PELV).
Ensure that the output voltage of the voltage supply for the

bus coupler does also not exceed 30.2 V in case of error.
Observe the general safety instructions, refer to

chapter 2.2

"General safety instructions" on page 7

②

Loss of the safety function

due to load switching at maxi‐

mum leakage current

WARNING

●

At this current, note that the load may not be switched

and remain in the enabled state.

●

Observe that when selecting the actuator.

③

Loss of the safety function

due to load switching at mini‐

mum holding voltage

WARNING

●

At this voltage, note that the load may not be switched

and remain in the enabled state.

●

Observe that when selecting the actuator.

④

Loss of the safety function

due to the switch-on pulse

WARNING

●

Note that the load may neither fail nor react safety-criti‐

cally if the switch-on pulse (light test) is 1 ms.

●

Observe that when selecting the actuator.

⑤

This switch-off pulse can

cause the loss of the safety

function.

WARNING

●

Note that the load may not react safety-critically if the

switch-off pulse (dark test) is 3 ms.

●

Observe that when selecting the actuator.

Loss of the safety function

due to parasitic voltage

WARNING

●

Connect the ground of the actuator to the respective

ground terminal point of the corresponding output on the

IndraControl S20 plug. Using an external ground is not

permitted.

●

The connected load may not dangerously react on test

pulses.

11.2.9

Approvals

For the current approvals, go to

www.boschrexroth.com/electrics

Bosch Rexroth AG

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

60/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

Technical data and ordering data

Содержание Rexroth IndraControl S20

























































































Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl S20, Руководство пользователя

Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды