Bosch Rexroth IndraControl S20 страница 10 Скачать руководство пользователя

Страница: 10 / 88

Documentation

Observe all specifications in this manual and other applicable documents, re‐

fer to

chapter 2.7 "Documentation" on page 9

Personal and property protection

Personal and property protection can only be ensured if the module is used

as intended, refer to

chapter 2.6 "Intended use" on page 9

Error detection

Depending on the wiring and the parameterization, the module detects errors

in the safety-related installations.

Do not repair or make any

changes!

Repairs or user-specific changes at the module are prohibited. The housing

must not be opened. The module is protected against manipulations using

protective labels. In case of unauthorized repair or opening of the housing,

the protective label is damaged. The function of the safety module is not

guaranteed anymore in this case.
In case of error, send the module to Bosch Rexroth or contact the Bosch

Rexroth service immediately.

Interchanging or reversing polarity

of the connections

Ensure that the connections are neither interchanged, polarity is not reversed

nor manipulated. To better impede interchanging, plugs and slot markings

are colored.

2.3

Electrical safety

Loss of the safety function and presence of

hazardous shock currents due to an incorrect

installation.

WARNING

●

Observe the notes on electric safety.

●

Design the module used and perform their installation in the system ac‐

cording to the specific requirements.

●

Check the systems upgraded with Csos again.

Direct and indirect touching

Ensure that all components connected to the system are protected against di‐

rect and indirect touching acc. to VDE 0100 part 410. If an error occurs, no

hazardous parasitic voltages may occur (single-failure proof!)
Required actions:
●

Use power supply units with protective separation (PELV)

●

Decoupling circuits, which are no PELV systems, via opto-couplers, re‐

lays and other components meeting the requirements on the safe sepa‐

ration.

Power supply units for 24 V supply

Only use power supply units with protective separation and PELV voltage ac‐

cording to EN 50178/VDE 0160 (PELV). These power supply units exclude

short circuits between the primary and the secondary side.
Ensure that the output voltage of the voltage supply does also not exceed 32

V in case of error.

Insulation measurement

Observe the dirt and overvoltages at runtime when selecting equipment.
The module is designed for overvoltage category II (acc. to DIN EN 60664-1).

If overvoltages exceeding the values (defined in overvoltage category II) are

expected in the system, take additional measures to limit the voltage.

2.4

Safety of machine or system

The machine or system vendor as well as the operator are reliable for the

safety of machine or system and the application used in the machine or sys‐

tem.

Bosch Rexroth AG

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

8/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

For your safety

Содержание Rexroth IndraControl S20

























































































Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl S20, Руководство пользователя

Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды