Bosch Rexroth IndraControl S20 страница 40 Скачать руководство пользователя

Страница: 40 / 88

Parameterization

Parameterized as

Notes

Switch-off delay for stop

category 1

Enabled

Or disabled

Test pulses (output disa‐

bled)

Enabled

Or disabled

7.5

Dual-channel assignment of the safe outputs

For the dual-channel assignment of the safe outputs, two adjacent outputs of

the same plug are used. This assignment cannot be parameterized, refer to

"Dual-channel" on page 29

K2 (R)

GND

OUT1_Ch2

K1 (R)

GND

OUT1_Ch1

Fig. 7-3:

Dual-channel assignment of the outputs

K1 (R) and K2 (R) represent the forced N/C contacts to the state monitoring

of the relay (read-back contacts).
●

Connect these contacts via safe digital outputs.

●

Analyze the readback and thus the state of the switching elements in

the safe application program.

Loss of the safety function due to parasitic

voltage

WARNING

Connect the ground of the actuator to the respective ground terminal point of

the corresponding output on the IndraControl S20 plug. Using an external

ground is not permitted.

The error detection time does not have to be considered for a dual-channel

assignment.

Key data

Actuator

Dual-channel

Attainable SIL/SILCL/Cat./PL

SIL 3/SILCL 3/cat. 4/PL e

Switch on the test pulses to improve the device diagnostics and in

case of long off-intervals.

Device diagnostics and module

behavior in case of error

Bosch Rexroth AG

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

38/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

Connection examples of the safe outputs

Содержание Rexroth IndraControl S20

























































































Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl S20, Руководство пользователя

Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды