Bosch Rexroth IndraControl S20 Скачать руководство пользователя

Страница: 7 / 88

Using safety instructions

1.1

Structure of the safety instructions

The safety instructions are structured as follows:

Burns and chemical burns due to wrong
battery treatment!

CAUTION

Safety alert symbol
Signal word

Consequences and
source of danger

Avoiding danger

Do not open the batteries and do not heat them over 80 °C.

Fig. 1-1:

Structure of the safety instructions

1.2

Explaining signal words and safety alert symbol

The safety instructions in this documentation contain specific signal words

(danger, warning, caution, notice) and, if necessary, a safety alert symbol

(according to ANSI Z535.6-2006).
The signal word is used to draw attention to the safety instruction and also

provides information on the severity of the hazard.
The safety alert symbol (a triangle with an exclamation point), which pre‐

cedes the signal words danger,warning and caution is used to alert the read‐

er to personal injury hazards.

DANGER

In the event of non-compliance with this safety instruction, death or serious

injury will occur.

WARNING

In the event of non-compliance with this safety instruction, death or serious

injury will occur.

CAUTION

In the event of non-compliance with this safety instruction, minor or moderate

injury can occur.

NOTICE

In the event of non-compliance with this safety instruction, material damage

can occur.

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

Bosch Rexroth AG

5/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

Using safety instructions

Содержание Rexroth IndraControl S20

























































































Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды

Bosch Rexroth IndraControl S20, Руководство пользователя

Результаты поиска

Содержание Rexroth IndraControl S20

Отзывы:

Похожие инструкции для Rexroth IndraControl S20

Бренды по названию

Популярные бренды