manualshive.com logo in svg

Bosch Rexroth IndraControl S20, Руководство пользователя

Поделиться
Скачать
Bosch Rexroth IndraControl S20 Скачать руководство пользователя страница 57

11 

Technical data and ordering data

11.1 

System data CSos

CSos edition

2.8

Module processing time

2 ms

Tab. 11-1:

CSos system data

For  the  system  data,  refer  to  the  documentation  of  the  control

used.

11.2 

Module data of the S20-SSDO 8/3

11.2.1 

General data

Size and weight
Housing dimensions without bus

base module with plug (width ×

height × depth)

53.6 mm × 126.1 mm × 54 mm

Weight (with plugs)

Approx. 220 g

Operation mode
CSos

Extended data format with 12 bytes

Ambient temperature
Operation

-35 to +60 ℃ (any installation location)
–35 °C to +55 °C (acc. to CULUS; max. total cur‐

rent of 6 A; 4 Outs loaded with 1.5 A or 8 Outs

loaded with 0.75 A)

Storage and transport

–40 °C to +85 °C

Air humidity

Operation

①

75 % on average, 85 % occasionally

Storage and transport

②

75 % on average, 85 % occasionally

Air pressure
Operation

70 kPa to 108 kPa (up to 3,000 m above sea lev‐

el)

Storage and transport

66 kPa to 108 kPa (up to 3,500 m above sea lev‐

el)

Degree of protection

IP20; operation min. in installation space IP54

Housing material

Plastics PBT self-extinguishing (V0)

Clearance and creepage distan‐

ces

Acc. to IEC 60664-1

Protection class

III (protective extra-low voltage) acc. to IEC61140,

EN61140, VDE 0140-1

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P 

Bosch Rexroth AG

55/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

Technical data and ordering data

Содержание Rexroth IndraControl S20

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды