FPD-7024
|
Operation and Installation Guide | 3.0
System Operation
.
Bosch Security Systems, Inc. | 1/10 | F01U008458-03
27
Terminating the communicator test
function (with the [*/Back] key) resets the
communicator and discards all unsent
reports. When an off-normal condition
occurs during a Communicator test, the
test automatically resets, clearing all
reports, so the off-normal conditions are
sent normally.
3.4.3 Call for Remote Programming
Phone Numbers 1 and 3 must be programmed,
along with Account Code 1. The control panel calls
Phone Number 3 and attempts to connect for
downloading. If the control panel is already using
the phone line, it sounds the three-beep error tone.
This function requires an access code with
programming authority (Level 1).
3.4.4 Test Battery/NAC Circuits
If a power failure occurs, your control panel has a
built-in battery that continues to power the system
for several hours. The control panel automatically
recharges the battery when power is restored. In
this test mode, the system operates the local NAC
circuits and tests the battery for two seconds. The
test results are shown at the end of the test, and are
not reported to the central station. Pressing the
[*/Back] key or the [#/Enter] key returns the display
to standby mode, or the unit times out after three
minutes.
3.4.5 Answer for Remote Programming
The control panel immediately seizes the phone line
to answer a remote programming call. While
programming is underway, the Trouble LED flashes.
This also allows on-site PC downloading. If the
control panel already uses the phone line for a
report communication, it sounds the three-beep
error tone. This function requires an access code
with programming authority (Level 1).
3.4.6 Manually Activate Outputs
This test turns a selected output on and off
manually.
3.4.7 Read Zone Input Levels
This test shows the status of a selected on-board
point. The loop existing through the point is shown.
Normal loops show 11 to 15 mA. Loops in alarm
show over 25 mA, and loops in trouble show less
than 6 mA.
3.4.8 Addressable Point Test (MUX Test)
This test allows activation of the special test mode
for addressable (multiplex) devices. This applies
only if the optional D7039 Addressable Point Bus
Expander module is installed.
When this test mode is selected, the system asks
which bus to test, 1 or 2. Select 1 to test points 9 to
128 and select 2 to test points 129 to 255. The
system presents 5 options:
•
List Devices:
Shows the point numbers of all
devices on the selected bus. Some devices
(such as a dual point module) can use two or
more points
•
Show Holes:
Lists locations on the bus that
have no assigned device. This can help to find
programming errors or identify an available
address for a new device.
•
Show Extras:
The system scans the bus to
identify devices that are present on the bus, but
are not programmed into the system. Scanning
the bus takes about 60 sec to scan the bus.
Restoring the bus after scanning also takes
about 60 sec. The system cannot identify
devices above Address 128 on Bus 1, or below
Address 129 on Bus 2. If you know that a device
is connected to the system but cannot find it,
ensure that it is connected to the correct bus: 9
to 128 for Bus 1, 129 to 255 for Bus 2.
•
Show Missing:
Lists devices programmed into
the system but not present on the bus are listed.
Unless a device was programmed into the
system (such as using MUX EDIT), it is not
considered missing.
•
Show Status:
After you select a device and
press [#/Enter], this test shows detailed status
information for the selected device. Eight
conditions (not all status conditions apply to or
are supported by all devices) are shown. See
the display shown below (which updates
automatically every five seconds). For this
option, you can view the status of any MUX
device regardless of which bus you selected to
test when test mode was entered.
XxLxRxDxMxTxFxAx
x is either 0 or 1 depending on whether the
condition is false or true (0=false and 1=true).
The letters indicate the condition:
X:
Reserved for future use.
L:
Commanded relay state - this is how the
output relay should be set.
R:
Actual relay state - this is how the output
relay is actually set.
D:
Detector dirty - the detector is excessively
sensitive.