Bosch D7412GV2 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 148

background image

D9412GV2/D7412GV2 |

Program Entry Guide | 2.0

GV2MAIN

EN

| 64

Bosch Security Systems | 5/05 | F001U003636B

L## Send Report

Default:

Refer to the program record sheet

Selection:

Blank or E

Function No.

Function Name

Alternate Keystroke

13 Send

Report

[COMMAND][4][1]
or
[COMMAND][4][2]

Send a Test Report from any keypad assigned to an
area where the user has authority.

Access Control Functions

Use the following functions to control the doors from
the keypad. Users can have authority to access the
Door Control and can use all or part of the functions
within.

All doors display when this function is
selected. This function does not follow the
scope of the keypad.

L## Door Control

Default:

Refer to the program record sheet

Selection:

Blank or E

Function No.

Function Name

Alternate Keystroke

14 Door

Control

[COMMAND][4][6]

This item only allows programming access to the
following three sub-prompts. It does not affect the
user’s access to Cycle Door, Unlock Door, and Secure
Door.

Cycle Door, Unlock Door, and Secure Door
cannot be accessed through the Function
List. Door Control must be added to the
Function List to access the door control
functions, or COMMAND 46 can be used.

The following prompts are sub-functions of Door
Control. They become visible in the D5200
Programmer when you Enable Door Control and
press [ENTER] on the D5200.

Cycle Door must be enabled for all three
sub-functions to operate. If Cycle Door is
disabled, all three sub-functions do not
operate.

L## Cycle Door

Default:

Refer to the program record sheet

Selection:

Blank or E

Function No.

Function Name

Alternate Keystroke

(None)

Cycle Door

(Menu function only)

Cycle Door (Menu Function only)

To cycle the doors, press number [1] through [8] on
the keypad, corresponding to the door number. For
example, pressing [2] and [ENTER] cycles door
number 2, which is indicated by

C

in the display. Refer

to “Cycle Door” in

Table 27

on page 65.

Cycle Door allows the user with this authority level to
access the CYCLE? 12345678 function.

L## Unlock Door

Default:

Refer to the program record sheet

Selection: Blank or E

Function No.

Function Name

Alternate Keystroke

(None)

Unlock Door

(Menu function only)

To unlock or relock a door, press number [1] through
[8] on the keypad, correspoding to the door number
(refer to “Unlock Door” in

Table 27

on page 65). For

example, pressing [2] and [ENTER] unlocks door
number 2. The display indicates “U’ (for unlock door)
with the door number.

Unlock Door allows the user with this authority level
to access the UNLOCK? 12345678 function.

L## Secure Door

Default:

Refer to the program record sheet

Selection:

Blank or E

Function No.

Function Name

Alternate Keystroke

(None)

Secure Door

(Menu function only)

Press number [1] through [8] on the keypad,
corresponding to the door number to secure or
unsecure a door (refer to “Secure Door” in

Table 27

on

page 65).For example, pressing [2] and [ENTER]
secures door number 2, which is indicated by an

X

in

the display.

Secure Door allows the user with this authority level to
access the SECURE? 12345678 function.

«
...
62
63
64
65
66
...
»

Содержание D7412GV2





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для D7412GV2

Бренд: Samsung Страницы: 32

Harmony Controller 2000

Бренд: A10 Страницы: 27

Бренд: FAAC Страницы: 32

Бренд: Federal Signal Corporation Страницы: 60

Бренд: FASTRON. Страницы: 16

Бренд: Samson Страницы: 32

Бренд: Quantum Страницы: 15

ROBO Cylinder RCP2 Series

Бренд: IAI Страницы: 5

Бренд: NAPCO Страницы: 48

Magnum Alert 2600

Бренд: NAPCO Страницы: 68

Бренд: York Страницы: 20

Бренд: YASKAWA Страницы: 121

Бренд: YASKAWA Страницы: 17

Бренд: YASKAWA Страницы: 58

Бренд: YASKAWA Страницы: 30

MagicSpeed Series

Бренд: Waeco Страницы: 76

Бренд: Brand Innovations Страницы: 56

Бренд: AirCycler Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды