Bosch D7412GV2 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 148

background image

D9412GV2/D7412GV2 |

Program Entry Guide | 5.0

RADXSKED

EN

| 100

Bosch Security Systems | 5/05 | F001U003636B

W# Monday

Default:

No

Selection:

Yes or No

W# Tuesday

Default:

No

Selection:

Yes or No

W# Wednesday

Default:

No

Selection:

Yes or No

W# Thursday

Default:

No

Selection:

Yes or No

W# Friday

Default:

No

Selection:

Yes or No

W# Saturday

Default:

No

Selection:

Yes or No

W# Open Early Begin

Default:

00:00

Selection:

HH:MM (hours and minutes)

00:00 to 23:59

Open Early Begin:

This program item is one of three

required to create an Opening Window. To finish
programming an Opening Window, Open Window
Start and Open Window Stop must be programmed.

The time programmed in the

W# Open Early Begin

field is the earliest time that the user is allowed to open
an area before the Opening Window Start time. If
Opening and Closing Reports are enabled, disarming
the area between midnight and the open Early Begin
time generates an Opening Report.

•

If

A# Disable O/C in Window

is set to

Yes

and

the area is disarmed between the Open Early
Begin time and the Open Window Start time, the
Opening event is sent with an Early to Open
modifier. If the Open Early Begin time is the same
as the Open Window Start time, no Opening
Event is sent.

•

If

Disable O/C in Window

is set to

No

and the

area is disarmed at any time, an Opening Event is
sent without an Early to Open or Late to Open
modifier.

Disarming the area between the Open Window Start
and open Window Stop times creates a local event in
the control panel event log, but does not send the
Opening Report to the central station.

Disarming the area between the Open Window Stop
time and before the next window’s Open Early Begin
time (or midnight, whichever is earlier) generates an
Opening Event with a Late to Open modifier.

When configuring multiple windows to operate on the
same day, ensure that they are added to the system in
chronological order. For example, if three windows are
programmed to execute on Tuesday, Window 1 (W1)
must occur before Window 2 (W2), and Window 2
must occur before Window 3 (W3).

Avoid programming the Open Early Begin
time before a time that is between another
window’s Open Window Start and Open
Window Stop times.

Do

not

program a window to cross the

midnight boundary.

Disabled windows have a blank beginning time. If the
entry for this prompt is blank, but times are
programmed for Open Window Start and Open
Window Stop, the window is disabled.

To disable the window, all hours and minutes spaces
must be blank.

Make time entries using a 24-hour clock.
For example:

Midnight is entered as 00:00
7:00 AM is entered as 07:00
2:45 PM is entered as 14:45
11:59 PM is entered as 23:59

Reboot the control panel to activate today’s window, if
the window needs to activate on the same day you
program it.

«
...
98
99
100
101
102
...
»

Содержание D7412GV2





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для D7412GV2

Бренд: J4C Страницы: 4

Бренд: ABB Страницы: 6

Бренд: S&C Страницы: 40

Бренд: S&C Страницы: 34

Бренд: Xantrex Страницы: 56

Бренд: Xantrex Страницы: 2

Freedom Sequence

Бренд: Xantrex Страницы: 58

Бренд: Xantrex Страницы: 4

Бренд: Xantrex Страницы: 20

CentralControl CC41

Бренд: Becker Страницы: 48

Бренд: GSK Страницы: 32

Бренд: Viva Страницы: 9

COMBIVERT F4-S/1.2

Бренд: KEB Страницы: 96

Бренд: Fancom Страницы: 36

Бренд: Beninca Страницы: 8

DMX-LED-DIMMER X9 HR

Бренд: DMX4ALL Страницы: 14

Бренд: ABNOX Страницы: 108

Бренд: fadini Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды