Bosch D7412GV2 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 148

background image

D9412GV2/D7412GV2 |

Program Entry Guide | 2.0

GV2MAIN

EN

| 48

Bosch Security Systems | 5/05 | F001U003636B

CC# Assign Door

Default:

Blank

Selection:

1 to 8, Blank

Blank No door controller is assigned for adding

tokens or the

CLOSE DOOR #

appears on

the keypad.

1 to 8 Assign the door controller that enters the

Add User Mode when initiated. If the
assigned door remains open and this keypad
has the

CC# Close Door Warning Tone

set to

Yes

, the

CLOSE DOOR #

message

appears on this keypad.

Program the door number used by this keypad to add
tokens or cards and to show

CC Close Door

.

•

If a door is not programmed for this
prompt and a door is not assigned to
the area using the

D# Entry Area

in the

RADAXS handler,

IMPORTANT! 9210

NOT READY

appears at this keypad

when you attempt to add a user. The
message indicates that the control panel
cannot start the Add User Mode until a
door is assigned to this keypad.

•

Assigning a door to a keypad is not
necessary for the user to control the
door(s) using the Door Control function.
Any door that is active can be controlled
by a user who has the appropriate door
control authority. The door control
functions are available to a valid user at
any keypad with access to the area
where the door is assigned.

During the Add User Mode, tokens or
cards, door control requests, and RTE/REX
do not function. Put the Door Mode into an

unlocked

state before adding users if there

is heavy activity for this door.

CC# Trouble Tone

Default:

Yes

Selection:

Yes or No

Yes

Panel-wide trouble tones sound and
visual displays show at this keypad.

No

Panel-wide troubles do not sound.
Visual displays still show.

Determines whether this keypad, or any keypad with
the same address setting, emits the panel-wide trouble
tones (power, phone, SDI bus, and Zonex bus).

Panel-wide trouble tones do not include
Point Troubles, Buzz on Fault, or Close
Door Now.

Assign two CCs to the same area so one
keypad emits the tone and another does
not.

CC# Entry Tone

Default:

Yes

Selection:

Yes or No

Yes

This keypad sounds entry tones.

No

This keypad does not sound entry
tones.

Determines whether this keypad, or any keypad with
the same address setting, emits the Disarm Now entry
delay tone. Any Delay point within the area scope of
this keypad starts the entry sequence.

This prompt allows you to manage the tone
by keypad. Entry Tone can also be turned
off when programming your

P## Entry

Tone

off in

Point Index

.

Assign two CCs to the same area so one
keypad emits the tone and another does
not.

«
...
46
47
48
49
50
...
»

Содержание D7412GV2





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для D7412GV2

ServeRAID M5014

Бренд: IBM Страницы: 106

Бренд: Ransburg Страницы: 49

Бренд: Balboa Страницы: 2

Бренд: Badger Meter Страницы: 20

Бренд: Watts Страницы: 2

Бренд: Hanbay Страницы: 18

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 95

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 33

Бренд: Danfoss Страницы: 59

Бренд: Danfoss Страницы: 16

VLT AQUA Drive FC 200

Бренд: Danfoss Страницы: 91

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 100

Бренд: Danfoss Страницы: 82

Бренд: Danfoss Страницы: 18

Бренд: Danfoss Страницы: 12

OPTYMA Plus OP-LPQM

Бренд: Danfoss Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды