Bosch D7412GV2 Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 148

background image

D9412GV2/D7412GV2 |

Program Entry Guide | 5.0

RADXSKED

EN

| 108

Bosch Security Systems | 5/05 | F001U003636B

5.1.3

Holiday Indexes for User Group Windows

You can enable up to four Holiday Indexes to use with
User Group Windows. Enable at least one Holiday
Index if

UW# Xept Holiday

is programmed as

Yes

for this user window, or if you want this window to
activate only on specific dates. Holidays are
programmed in Holiday Indexes. Refer to

Section 5.3

Holiday Indexes

on page 117 for programming

information.

UW# Xept Holiday

Default:

No

Selection:

Yes or No

Determine if the window is disabled on holidays, or is
active only on holidays. Use the instructions provided
in the

W# Xept Holiday

prompt in

Section 5.1.1

Opening and Closing

on page 99.

UW# Holiday 1 [through 4]

Default:

No

Selection:

Yes or No

Yes

The selected holiday index can be
used by users in the User Group
window.

No

The selected holiday index does not
apply to users in this User Group.

5.2 Skeds

Use the Skeds module to program the control panel to
automatically execute functions that are otherwise
started by the end user at the keypad. Each sked can
be programmed to occur at a specific time on a
specific date or day of the week. Up to 40 Skeds can
be programmed.

A sked can be edited from the keypad if

S## Time

Edit?

is

Yes

. The date and time can be changed using

the Change Sked function.

Each sked number can be programmed with one of 24
functions for the

S## Function Code

. In addition to

the function, a choice must be made as to what is
affected by the function. For example, when choosing
Function 2 (Disarm Sked), the disarming is the
function and the selected areas are what is affected.

The functions and their associated parameters are
listed in the Sked Function Code Table in the

D9412GV/D7412GV2 Program Record Sheet

(P/N: F01U003635), and they are explained in detail
following the

S## Function Code

prompt on page

109.

Each sked can be programmed with up to four
Holiday Indexes. The Holiday Indexes can execute
the sked on the holidays as well as on the date or
day(s) of the week, or, they can prevent the sked from
executing on the holidays (refer to

S## Xept Holiday

prompt in this section

).

Sked Number

Default:

1

Selection:

1 to 40

Enter the number of the sked you are programming.

S## TimeEdit

Default:

Yes

Selection:

Yes or No

Yes

The user can edit the time of this
sked from the keypad and determines
if this sked appears in the CHG
SKED display.

No

The user cannot edit the time of this
sked from the keypad and the sked
does not appear in the CHG SKED
display.

Select whether the user can edit the time of this sked
from the keypad.

«
...
106
107
108
109
110
...
»

Содержание D7412GV2





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для D7412GV2

Бренд: Vacon Страницы: 62

Бренд: E-fly Страницы: 16

Бренд: Rain Bird Страницы: 48

Бренд: L. G. B. Страницы: 2

Бренд: L-Acoustics Страницы: 36

Бренд: Parker Страницы: 32

Бренд: Rayrun Страницы: 4

AeGIS 7000 Series

Бренд: PACH & COMPANY Страницы: 2

Бренд: PACH & COMPANY Страницы: 4

Бренд: Watts Страницы: 4

Бренд: WaterCop Страницы: 4

Бренд: Bartlett Страницы: 7

Бренд: Lab.gruppen Страницы: 2

Бренд: PUTCO Страницы: 2

Бренд: Grundfos Страницы: 16

Бренд: Loewe Страницы: 62

Бренд: Shimaden Страницы: 32

Бренд: Linak Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды