Bosch D7412GV2 Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 148

background image

D9412GV2/D7412GV2 |

Program Entry Guide | 4.0

RADXPNTS

EN

| 88

Bosch Security Systems | 5/05 | F001U003636B

If the point restores and the fire alarm is not
silenced from the keypad, the fire alarm
output continues until Fire Bell time expires.
If the point does not restore, the fire alarm
output continues even after bell time
expires.

Use this option for fire applications to meet
the requirement that audible alarms cannot
be silenced until the fault condition clears
or the Fire Bell time expires.

P## Audible After 2 Failures

Default:

No

Selection
:

Yes or No

Yes

A# Burg Alarm

relay activates after

two failed attempts.

No

P## Silent

points do not cause the

A#

Burg Alarm

relay to activate even if

the report does not get to the central
station receiver.

When set to Yes, if the report fails to reach the central
station after two attempts, a silent alarm rings the

A##

Burg Alarm

bell. A silent alarm is generated when a

point with

P## Silent

set to

Yes

is faulted while

armed.

When a point programmed for

P## Silent

Bell

is faulted, the timer for the

A# Burg

Time

starts, even though the bell is not yet

ringing. As much as three minutes can
elapse before the second attempt fails.
Ensure that

A# Burg Time

is programmed

to provide the amount of bell time you
need, minus the additional three minutes
that might elapse before the bell actually
begins to ring.

P## Invisible Pt

Default:

Refer to the program record sheet

Selection:

Yes or No

Yes

Keypads do not display alarm activity
from this point.

No

Activity from this point is visible at
the keypads.

Use this option to determine whether the point
appears in the keypad display upon an alarm
condition. For LED keypads, the LED does not
illuminate upon an alarm condition. Point text appears
and annunciation is made for Invisible points
programmed for a trouble condition in point response.

To prevent the keypad alarm tone and the

A# Burg Alarm

bell from sounding,

program

P## Silence Bell

as

Yes

.

If a user enters a valid pass code while a
bell is ringing for an invisible alarm, the
keypad shows

ALARM SILENCED

.

«
...
86
87
88
89
90
...
»

Содержание D7412GV2





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для D7412GV2

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 26

Бренд: NAiS Страницы: 199

Бренд: Panasonic Страницы: 38

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 179

Бренд: Panasonic Страницы: 23

Бренд: Panasonic Страницы: 30

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 20

INDUSTRY PAN9028

Бренд: Panasonic Страницы: 34

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 20

Бренд: Daktronics Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды