Bosch D7412GV2 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 148

background image

D9412GV2/D7412GV2 |

Program Entry Guide | 2.0

GV2MAIN

EN

| 36

Bosch Security Systems | 5/05 | F001U003636B

A# Area Type

Default:

Regular

Selection:

Regular, Master, Associate, or Shared

Regular

Arms or disarms as an independent area.

Master

Does not allow arming for this area unless all associate areas with the same A# account number
are master exit delay armed or master armed.

CHK AREA

displays if the associate areas are not

armed.

Exception:

RPS allows master areas to be armed without all associate areas being in the

armed state.

A master area can be disarmed regardless of the armed state of the other areas in the account.

Multiple master areas can be programmed in a single account.

CC# Scope

affects master arming.

Area:

When arming a master area that has

CC# Scope

set to

Area

for all

keypads, all associate areas within the same account must first be armed
independently by other means.

Panel Wide or Account Wide:

When arming a master area from a keypad with

CC# Scope

set to

Panel Wide

or

Account Wide,

all associate areas enters

exit delay as soon as the master area is armed. If there is a shared area within
the same account, it begins its exit delay after all associate areas are armed.

Using the arming sked (

S## Function 1

) requires that you first use an arming

sked to arm the associate areas before using an arming sked to arm the
master area. Arming master areas with RPS, Keyswitch, or Auto Close
parameters (refer to Open/Close Options) occurs before all associate areas
are armed

Associate

Allows arming and disarming regardless of the armed state of the other areas with the same A#
account number. Use this area type with a master area and associate it by using the same account
number.

Keypads assigned to associate areas, when used with shared areas, must
have

CC# Scope

programmed.

Shared

Shared areas cannot be armed using a passcode, key switch, token or card, sked, or RPS.

The scope of all associate areas must include the shared area(s) in order to view
faulted points.

«
...
34
35
36
37
38
...
»

Содержание D7412GV2





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для D7412GV2

Бренд: DAV TECH Страницы: 10

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 20

Бренд: Danfoss Страницы: 32

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 44

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 144

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 64

Бренд: Danfoss Страницы: 8

VLT AutomationDrive FC 360

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 6

Бренд: Danfoss Страницы: 4

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 2

ECL Comfort 110

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 24

Бренд: EasyIO Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды