background image

-28- 

Revision 7/F3527 

© 

Moffat Ltd, November 2004 

6.1.4 FAN DOESN’T OPERATE 

Fan motor faulty 

Check the supply voltage across motor termi-
nals.  If there is no voltage then check the 
electrical connections of wiring. 
If voltage is correct then check the oven fan 
for free rotation.  Remove any obstruction. 
If fan is free to spin and the voltage at motor 
terminals is correct, then the motor is faulty—
replace. 
 

Fan switch faulty

 

Check that the thermostat has power to  
terminal 5 on switch body on the front of the 
thermostat when power switch is ON.  If no 
voltage check wiring,  check that terminal P5 
has power switched to it when the thermostat 
is turned on.  If no power to P5 then switch is 
faulty and thermostat complete with switch 
needs to be replaced. 

6.1.5 OVEN LIGHTS NOT ILLUMINATING—
DOOR OPEN (AUTOMATICALLY ON) 

No power to lights 

Check the supply voltage across lamp hous-
ing terminals at RH side rear of oven.  If the 
voltage is correct, replace the bulb (if faulty).  
If the bulb is OK, check lamp housing.        
Replace if faulty. 

6.1.6 OVEN LIGHTS NOT ILLUMINATING—
DOOR CLOSED (MANUALLY SWITCHED 
ON) 

Light switch faulty 

Check voltage to the bottom terminal of the 
switch.  If there is no voltage, then check    
wiring. 
With switch depressed, check voltage at top 
terminal.  If there is no voltage, then replace 
the switch. 
If voltage is correct, then check wiring to light. 

NOTE:

  Alternately, perform a continuity test 

across the terminals with the light 
switch depressed. 

6.1.7 NO WATER INJECTION / STEAM 

Steam switch faulty 

Check voltage to the bottom terminal of the 
switch.  If there is no voltage, then check    
wiring. 
With switch depressed, check voltage at top 
terminal.  If there is no voltage, then replace 
the switch. 
If voltage is correct, then check wiring to the 
solenoid. 

NOTE:

  Alternately, perform a continuity test 

across the terminals with the steam switch  
depressed.

 

 
Fault with water valve 

Check voltage supply across the water valve 

Thermostat faulty 

Set thermostat to 200°C or 400°F.  Check the 
voltage out of terminal 1 on the thermostat.  If 
there is no voltage then the thermostat is 
faulty—replace. 
If the voltage is correct and the heating light is 
on then check all wiring to heating contactor. 

Microswitch 

com 

n.c. 

Figure 6.1.3 

Burner faulty

 

With burner removed (refer 6.3.22), inspect 
burner for leak holes in construction and  
deterioration in mesh surfaces.  Tears or  
corrosion holes in mesh will be evidence of 
faulty burner condition.  Replace burner if 
faulty. 

NOTE:

  Minor mesh surface buckling is  

normal, and will not necessitate burner 

 

replacement. 

6.1.3  BURNER NOISY 

these terminals when ‘Roast ‘n Hold’ is not 
selected. 

If there is no voltage, open oven door and 
manually depress door microswitch actuator 
at bottom right of oven.  If this activates the 
lights, then the microswitch actuator arm     
behind the control panel requires adjustment. 
Check voltage across micro-switch terminals 
to neutral. 
With the door open there should be power to 
the com terminal and the n.c. terminal. 
If not, microswitch is faulty—replace. 

Содержание 203926













































































Отзывы: