BIO RAD VERSADOC Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 61

background image

User’s Manual

•

1-2

1.2 Safety Information

This instrument is meant for Laboratory use only and should not be
used in any other way or manner that is not specified in this Manual.

Your safety and the safety of others are very important to us. To help you
make informed decisions about safety, we have provided comprehensive
operating procedures and safety information in this manual and on labels
affixed to instrumentation. This information will alert you to any potential
hazards. It is the user's responsibility to take time and read and understand
the Safety Information and put it to the best use for a Safe operation of the
system.

1.2.1 General Cautions

Caution: Ensure that all of the systems ventilation openings are free of
interference. Excessive heat build up in the instrument may effect performance
or cause operational failure.

Caution: With the exception of cleaning or replacing light bulbs, refer all
servicing to qualified Bio-Rad personnel or their agents. If you experience
technical difficulties with the instrument contact Bio-Rad to schedule a service
appointment. The instrument should not be modified or altered in any way.
Alteration of this instrument voids the manufacturer’s warranty and may create a
potential safety hazard for the user.

Caution: Bio-Rad is not responsible for any injury or damage caused by the use
of this instrument for purposes other than that for which it is intended or by the
modification of this instrument when not performed by qualified Bio-Rad
personnel or an authorized agent.

1.2.2 General Warnings

Warning: This instrument must be connected to an appropriate AC voltage
outlet that is properly grounded.

Warning: There are hazardous voltages inside the rear panel of the

VersaDoc



. Do not remove the cover to the Electronics back panel when the

instrument is connected to AC power.

Warning: Do not defeat any instrument interlocks; they are designed to
prevent user injury.

Warning: The

VersaDoc



weighs 44 kg (96 lbs.) depending on which camera

you have purchased. Exercise caution when lifting the instrument. It is
recommended that at least two persons lift the instrument. Lift the instrument
by the bottom plate. Never lift the instrument by opening at the top which is
the plastic camera mounting plate because this will cause light leaks and
damage the camera mounting plate.

«
...
6
7
8
9
10
...
»

Содержание VERSADOC






























































Отзывы:

Нет отзывов

Похожие инструкции для VERSADOC

PIXMA MX882 Series

Бренд: Canon Страницы: 34

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 913

Laser Class 700 Series

Бренд: Canon Страницы: 30

Laser Class 700 Series

Бренд: Canon Страницы: 6

Laser Class 700 Series

Бренд: Canon Страницы: 6

Laser Class 700 Series

Бренд: Canon Страницы: 108

PIXMA MX860 series

Бренд: Canon Страницы: 9

imagePROGRAF iPF9400

Бренд: Canon Страницы: 8

PIXMA MX860 series

Бренд: Canon Страницы: 93

Бренд: Canon Страницы: 20

Бренд: Canon Страницы: 30

Бренд: Canon Страницы: 2

4250 - WorkCentre - Copier

Бренд: Xerox Страницы: 210

4150 - WorkCentre B/W Laser

Бренд: Xerox Страницы: 4

4118P - WorkCentre B/W Laser

Бренд: Xerox Страницы: 16

3635MFP - Phaser B/W Laser

Бренд: Xerox Страницы: 10

3635MFP - Phaser B/W Laser

Бренд: Xerox Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды