BIO RAD VERSADOC Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 61

background image

Welcome

Dear Customer,

On behalf of Bio-Rad Laboratories, we would like to thank you for investing in the

VersaDoc



Imaging System and we are sure that it will provide you with many years of

high quality imaging.

One of the best ways to familiarize yourself with the capabilities of your new VersaDoc
system is to read this manual. In it, you will learn how to set up the system and operate
all hardware components. It is also recommended that you read the accompanying
software manual to familiarize yourself with general acquisition functions and data
analysis. After reading this manual, please keep it close to your system so that it can be
conveniently referred to.

Your VersaDoc system is protected by a comprehensive instrument warranty agreement.
Please read this manual thoroughly, so that you fully understand the coverage provided
and are aware of your rights and responsibilities. One of the responsibilities of system
ownership is regular maintenance. Following the maintenance instructions provided with
this manual will help to keep your system and peripherals functioning optimally and will
protect your investment. Please also keep in mind that Bio-Rad offers a range of
comprehensive service agreements that can be tailored to meet your specific needs.

Bio-Rad Laboratories is dedicated to your total satisfaction and would be pleased to
answer any questions that you may have.

How to Contact Bio-Rad Laboratories

In the United States you can reach Bio-Rad Laboratories at the following numbers:

For general information
Toll free:

1-800- 4BIORAD

1-800-424-6723
Fax:

1-510-741-5802

email:

[email protected]

For service or technical assistance
Toll free:

1-800-424-6723

Fax:

1-510-741-5802

For information concerning Bio-Rad Laboratories and its products, visit our Worldwide
Web site at

http://www.bio-rad.com

«
1
2
3
4
5
...
»

Содержание VERSADOC






























































Отзывы:

Нет отзывов

Похожие инструкции для VERSADOC

Бренд: Samsung Страницы: 9

Bixolon SRP-500

Бренд: Samsung Страницы: 27

550N - CLP Color Laser Printer

Бренд: Samsung Страницы: 288

2 COLOR THERMAL PRINTER SRP-275

Бренд: Samsung Страницы: 8

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 91

Бренд: DataCard Страницы: 25

Бренд: Oki Страницы: 4

Бренд: Konica Minolta Страницы: 84

Бренд: Avery Weigh-Tronix Страницы: 40

Бренд: Copystar Страницы: 4

Бренд: Oki Страницы: 2

Бренд: Canon Страницы: 707

Бренд: Canon Страницы: 339

Бренд: DataCard Страницы: 204

Бренд: SP Страницы: 40

TASKalfa 2551ci

Бренд: Kyocera Страницы: 66

Бренд: WOOSIM Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды