BIO RAD VERSADOC Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 61

background image

User's Manual

•

3-14

Warning: This instrument must be connected to an appropriate AC
voltage mains outlet that is properly grounded.

Warning: There are hazardous voltages inside the rear panel of the
VersaDoc. Do not remove the cover to the electronics back panel when
the instrument is connected to AC power.

Power entry module at the
bottom right of the rear

panel

Power entry module

Figure 3.16

VersaDoc Connections:

The VersaDoc is connected to the host computer via a Serial or USB
interface and an AIA interface.

One each of the Serial and USB port is located on the rear right side of the
unit. Use the supplied USB or Serial Cable to connect the PC to the
VersaDoc.

Caution: To prevent damage to the hardware, all instruments must be
turned off before attempting to connect (or disconnect) the unit to the
host computer.

Upon insertion of the Serial or USB cable into the VersaDoc, the Serial or USB
port the PC will automatically select operation and sense the presence of
VersaDoc.

NOTE: Do not turn ON the power to the VersaDoc (and CEU in case of VersaDoc
5000) yet!

«
...
26
27
28
29
30
...
»

Содержание VERSADOC






























































Отзывы:

Нет отзывов

Похожие инструкции для VERSADOC

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 52

Бренд: Oki Страницы: 117

Бренд: Oki Страницы: 45

Бренд: Oki Страницы: 112

Бренд: Oki Страницы: 115

Бренд: Oki Страницы: 2

Бренд: Xerox Страницы: 108

Бренд: Xante Страницы: 21

Бренд: Keeler Страницы: 25

DocuPrint C2200

Бренд: Xerox Страницы: 200

Бренд: Hanin Страницы: 76

Бренд: SPRT Страницы: 48

Бренд: Panduit Страницы: 85

Бренд: Konica Minolta Страницы: 285

Бренд: Graphic Products Страницы: 28

ExpressCard 500

Бренд: Magtek Страницы: 49

Бренд: Xante Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды