BERTHOLD TECHNOLOGIES LB 8300 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 58

background image

6 Maintenance and Repair

Rod source shields LB 8300

36

64217BA2 Rev. 00, 10/2017

5.

Remove the O-ring (Fig. 12, item 2).

j

CAUTION

Danger caused by ionising radiation
When the source is removed, the unshielded source must be handled at short

time. An increased exposure to radiation may lead to damage to health.



Hold the source only with pliers.



Keep the source far from the body.



Ensure that no persons are in the field of radiation during the work.

1
2

3
4
5
6

Threaded rod
Source holder

Source
Protective cover
Locking plug transport shield
Cover transport shield

Fig. 13

Remove source out of shield

6.

Screw the threaded rod (Fig. 13, item 1) into the thread of the source holder
(Fig. 13, item 2).

7.

Pull the source out of the shield at the threaded rod. Hold the source (Fig.
13, item 3) with pliers.

8.

Insert the source as quickly as possible into the provided and opened
transport shield (Fig. 13, item.4) and close the locking plug (Fig. 13, item 5)
and the cover (Fig. 13, item 6).

«
...
34
35
36
37
38
...
»

Содержание LB 8300



























































Отзывы:

Нет отзывов

Похожие инструкции для LB 8300

Бренд: Parker Страницы: 5

Бренд: Bacharach Страницы: 31

Бренд: Bacharach Страницы: 2

Бренд: Harken Страницы: 4

Бренд: Harken Страницы: 2

TERRA FORCE BOOM

Бренд: Hardi Страницы: 40

Бренд: Harken Страницы: 4

QuickSlide HemaPRO

Бренд: Hardy Diagnostics Страницы: 2

Бренд: Hardt Страницы: 2

Бренд: Quivogne Страницы: 13

SimMan 3G Trauma

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 60

Бренд: laerdal Страницы: 4

Resusci Anne Simulator

Бренд: laerdal Страницы: 8

Nursing Baby VitalSim

Бренд: laerdal Страницы: 15

Бренд: laerdal Страницы: 9

Бренд: Tactile Medical Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды