BERTHOLD TECHNOLOGIES LB 8300 Скачать руководство пользователя страница 8

Страница: 8 / 58

1 About this operating manual

Rod source shields LB 8300

64217BA2 Rev. 00, 10/2017

1.8

Symbols Used

1.8.1

Structure of Warnings

Signal word

Source and consequence
Explanation, if required



Measure

In case of emergency

•

Warning symbols:

(warning triangle) draws attention to the hazard

•

Signal word:

states the severity of the hazard

•

Source:

states the type and source of the hazard

•

Consequence:

describes the consequences if warning is ignored

•

Measure:

states how one can avoid the hazard.

•

In case of emergency:

states how to react in case of direct danger.

Warning levels used

In this manual, warning instructions in front of instructions for action refer to
risks of injury or damage to property. The hazard-prevention measures described
must be observed.

DANGER

Indicates an imminent, major hazard, which will certainly result in serious
injuries or even death if the hazard is not avoided.

WARNING

Indicates a potential hazard, which can result in serious injuries or even death
if the hazard is not avoided.

CAUTION

Refers to a potentially dangerous situation, which can result in medium or

minor physical injuries or damages to property, if it is not avoided.

NOTICE

If this information is not observed, deterioration in the operation and/or

property damage may occur.

Содержание LB 8300



























































Результаты поиска

Содержание LB 8300

Отзывы:

Похожие инструкции для LB 8300

Бренды по названию

Популярные бренды

BERTHOLD TECHNOLOGIES LB 8300, Руководство по эксплуатации

Результаты поиска

Содержание LB 8300

Отзывы:

Похожие инструкции для LB 8300

Бренды по названию

Популярные бренды