BERTHOLD TECHNOLOGIES LB 8300 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 58

background image

Rod source shields LB 8300

7 Decommissioning

64217BA2 Rev. 00, 10/2017

41

7

Decommissioning

7.1

Safety instructions

j

WARNING

Danger of injury by falling loads



Never stand underneath a lifted or suspended load, keep at a safe
distance.



Only use tested sling gear components appropriate for the transport

weight.



Exclusively use the provided fixing possibilities (lifting brackets) for
attaching the sling gear.



Wear head protection and safety shoes.

j

CAUTION

Danger of injury caused by heavy and bulky system components



Heavy and bulky system components should only be handled using aids
and by at least 2 persons.



Observe the guidelines for safe handling of heavy loads.



Ensure stability and use the provided fixing possibilities.

j

CAUTION

Danger caused by nuclear radiation
Shields usually contain radioactive sources. An increased exposure to radiation

may lead to damage to health.



Consult the radiation safety officer responsible for your company.



Transport the source exclusively inside the closed and secured shield.

IMPORTANT

The applicable national regulations of the country of use have to be observed.

«
...
39
40
41
42
43
...
»

Содержание LB 8300



























































Отзывы:

Нет отзывов

Похожие инструкции для LB 8300

Бренд: Keiser Страницы: 82

Бренд: Keiser Страницы: 4

Бренд: Ognibene Страницы: 28

Бренд: Hameg Страницы: 24

Бренд: Vaisala Страницы: 118

Бренд: Taylor-Wharton Страницы: 25

Бренд: i-CAT Страницы: 96

Бренд: Latham Страницы: 4

Бренд: SafeWaze Страницы: 23

Бренд: Launch Страницы: 3

Бренд: Launch Страницы: 43

Бренд: Launch Страницы: 8

Бренд: Launch Страницы: 67

Бренд: Launch Страницы: 55

Бренд: LAUNCH TECH Страницы: 14

X-431 PROS V4.0

Бренд: Launch Страницы: 80

Бренд: Yamaha Страницы: 4

Бренд: Wacker Neuson Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды