HD-14T Four Post Lift
54
P/N 5900037 — Rev. F — February 2022
Anchoring the Posts
Install one Anchor Bolt (
5530456
) in each corner of each Base Plate, 4 per Post, 16 Anchor Bolts total.
Concrete specifications are:
•
Depth
: 4.25 inches, minimum
•
PSI
: 3,000 PSI, minimum
•
Cured
: 28 days, minimum
Anchor Bolt specifications are:
•
Length
: 4.75 inches
•
Diameter
: .75 inch
•
Anchor torque
: 85-95 pound feet (do
not
Torque less than 80 or more than 105)
⚠
WARNING
Your Concrete and Anchor Bolts
must
meet these specifications. Only install your
Lift on a Concrete surface. If you install a Lift on asphalt or any other surface, or
your Concrete or Anchor Bolts do not meet these specifications, it could lead to
product damage, Vehicle damage, personal injury, or even death.
BendPak Lifts are supplied with installation instructions and concrete fasteners meeting the criteria as
prescribed by the American National Standard “Automotive Lifts – Safety Requirements for
Construction, Testing, and Validation” ANSI/ALI ALCTV.
⚠
WARNING
Use only the Anchor Bolts that came with your Lift. If you use components from a
different source, you void your warranty and compromise the safety of everyone
who installs or operates the Lift.
Lift buyers are responsible for conforming to all regional, structural, and seismic anchoring
requirements specified by any other agencies and/or codes, such as the Uniform Building Code and/or
International Building Code.
To anchor the Posts
:
1.
Locate the hardware you will need: four Anchor Bolts, four Nuts, and four washers
per Post
.
2.
Using the Base Plates as guides, drill the holes —one hole in each corner of the Base Plate, so
four holes total per Base Plate.
Important
:
Do
not
drill all the way through the concrete; if you punch completely through the
slab, you compromise the holding strength of the Anchor Bolt once put into place.
Go in straight, in the center of the hole; do not let the drill wobble.
Use a carbide bit (conforming to ANSI B212.15).
The diameter of the drill bit must be the same as the diameter of the
Anchor Bolt. So if you are using a ¾ inch diameter Anchor Bolt, for
example, use a ¾ inch diameter drill bit.
3.
Vacuum each hole clean.
⚠
CAUTION
You must wear the proper safety gear for all drilling operations.
Содержание HD-14T
