BendPak HD-14T Скачать руководство пользователя страница 18

Страница: 18 / 76

HD-14T Four Post Lift

P/N 5900037 — Rev. F — February 2022

Deciding the Lift Orientation

Before going any further, decide how you want to orient your Lift. This decision affects where you will
place your Power Post and also the positioning of the Runways, which are

not

interchangeable.

The Powerside Runway and

must

be installed next to the Power Post. You can choose to position

your Power Post at either the

Front Driver-Side

or the

Rear Passenger-Side

. The Drive-up

Ramps are not affected by the Power Post location.
The drawings in this manual show the Power Post at the

Rear Passenger-Side

, but that does not

mean you have to. In many cases, the main factor is the location of the power source; many

customers prefer to place their Power Post (which holds the Power Unit) near the power source. If

power is not an issue, choose the option below that best fits your setup.

Important

Installers, you need to have the Lift owner make this decision no later than when
moving the Posts into position.

Power Post Location –

Front Driver-side

Power Post Location –

Rear Passenger-side

Содержание HD-14T












































































Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды

BendPak HD-14T, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды