BendPak HD-14T Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 76

background image

HD-14T Four Post Lift

48

P/N 5900037 — Rev. F — February 2022

Installing the Pushbutton Air Valve

The Pushbutton Air Valve is used to lower the Runways. It can go on either side of the Power Unit, but

we recommend placing it on the side facing

away

from the Lift to be out of the way.

For the customer-supplied air pressure, a minimum of 50 to 150 psi / 3 to 25 cfm is required.

Drawing shows the Pushbutton Air Valve Assembly and its connections to the Mounting Bracket on

the Power Post. Not all components shown. Sample Power Unit shown.

To install the Pushbutton Air Valve

:

1.

Find the necessary components: Zero Angle Bracket and the Pushbutton Air Valve Assembly.

2.

Connect the Zero Angle Bracket at the desired location (if it has not already been connected).
The best location is one that is visible and easily reached by the Lift operator.

3.

Connect the Pushbutton Air Valve to the Zero Angle Bracket.
Use the two holes on the Pushbutton Air Valve on the side away from the actual pushbutton. If you

use the holes next to the pushbutton, the Zero Angle Bracket interferes with the pushbutton when
you try to use it.

4.

Connect the Air Line Compression Elbow Fitting and the Straight Expander Fitting to the

appropriate locations on the Pushbutton Air Valve.
The Elbow Fitting connects to the opening labelled

CYL

. The Straight Fitting to the opening

labelled

IN

. See the drawing above.

5.

Attach the Air Line to the Compression Fitting and the customer-supplied air to the Straight Fitting.

NOTICE

:

The Return Line also comes out of the Flex Tube and is the same kind of tubing as the
Air Line.

Do not attach the Return Line to the Pushbutton Air Valve by

mistake

. Double check to make sure you are attaching the Air Line to the Pushbutton

Air Valve.

«
...
46
47
48
49
50
...
»

Содержание HD-14T













































































Отзывы:

Нет отзывов

Похожие инструкции для HD-14T

Бренд: Xantrex Страницы: 4

Бренд: Xantrex Страницы: 20

Бренд: Zmotion Страницы: 48

Бренд: Truweld Equipment Страницы: 28

Бренд: TradeQuip Страницы: 9

Masterweld 204T

Бренд: AES Страницы: 31

Бренд: Ewellix Страницы: 18

Бренд: VENCO Страницы: 21

Бренд: Woodward Страницы: 112

Бренд: GANTERUD Страницы: 24

KPH 370.70 LIKT

Бренд: rav Страницы: 82

Бренд: Paton Страницы: 17

Бренд: Riello Страницы: 2

Markoprint iJET

Бренд: Weber Страницы: 127

Бренд: Wesco Страницы: 20

DuplicAir Intelligent Control Blue

Бренд: Jydepejsen Страницы: 52

Бренд: Interroll Страницы: 54

Бренд: ICP DAS USA Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды