BendPak HD-14T Скачать руководство пользователя страница 52

Страница: 52 / 76

HD-14T Four Post Lift

P/N 5900037 — Rev. F — February 2022

Installing a Power Disconnect Switch

⚠

WARNING

A main Power Disconnect Switch is

not

provided with this equipment.

A Power Disconnect Switch is a National Electrical Code

(NEC) requirement. They are designed to interrupt

electrical power in the event of an electrical circuit fault,

emergency situation, or when equipment is undergoing
service or maintenance.
You must install a UL Listed Power Disconnect Switch

that is properly rated for the incoming power.

⚠

DANGER

All wiring

must

be performed by a

licensed, certified Electrician in

accordance with national and local

codes.

Your Power Disconnect Switch must be readily

accessible and installed so that it is in easy reach of the

Lift operator. It must be clearly and legibly marked to

indicate its purpose.
The drawing to the right shows a toggle Power

Disconnect Switch between the Lift’s power source and

its Power Unit. A quick flip of the switch immediately

cuts power to the Lift.
Make sure to have a certified Electrician install the Power

Disconnect Switch.
Make sure the electrician selects a

UL-listed

Power

Disconnect Switch.

Installing a Thermal Disconnect Switch

⚠

WARNING

The Lift’s motor does

not

have thermal overload protection.

Connect a motor Thermal Disconnect Switch or overload device that will make sure the equipment

shuts down in the event of an overload or an overheated motor.

⚠

DANGER

All wiring

must

be performed by a licensed, certified Electrician in accordance with

national and local codes.

High electrical current that exceed the motor’s full load amps (FLA) rating may result in permanent
damage to the motor.
BendPak strongly recommends you

not

exceed the rated duty cycle of the Lift’s motor.

Содержание HD-14T












































































Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды

BendPak HD-14T, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды