BendPak HD-14T Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 76

background image

HD-14T Four Post Lift

44

P/N 5900037 — Rev. F — February 2022

To install the Air Lines

:

1.

Find the roll of supplied ¼ inch, black, polyethylene Tubing and three Air Line Tee Fittings.

2.

Measure the distances for each of the seven (7) Tubing pieces you will need (see the drawing on

the previous page) for the Air Lines.

3.

Cut seven pieces of Tubing to the measured lengths from the roll of Tubing.

4.

Connect the various pieces of Tubing to the Air Line Tee Fittings on the Lift, as shown in the

drawing on the previous page for the locations of the Tubing pieces.

Make sure to position the three Air Line Tee Fittings as shown in the previous

drawing

.

Also, route the long Tubing piece that goes under the Powerside Runway through the Steel Tubes;

they keep Air Lines are out of the way of where the Cables will be routed.

⚠

WARNING

Make sure to route the Tubing pieces on the

outside

ends of the Front and Rear

Crosstubes through the Steel Tubes on the ends of the Crosstubes. This keeps the

Tubing and the Tee Connectors from being disturbed as you use the Lift. This is

important, because if the Air Lines are disturbed, the Safety Locks on the Lift may

not work correctly. If you notice that Tubing has become disconnected from an Air
Line Tee Connector, take the Lift out of service and get the Air Lines fixed.

Refer to

Working with Compression Fittings and Tubing

for more information about

connecting the Tubing to the Air Line Tee Connectors.

5.

Leave the Power Unit end of the Air Line hanging out of the Flex Tube opening for now.
It will be connected to a Tee Fitting and the Pushbutton Air Valve later.

«
...
42
43
44
45
46
...
»

Содержание HD-14T













































































Отзывы:

Нет отзывов

Похожие инструкции для HD-14T

Бренд: Wayne-Dalton Страницы: 24

Бренд: Eastwood Страницы: 12

Бренд: Eastwood Страницы: 16

Бренд: Eastwood Страницы: 4

Бренд: Eastwood Страницы: 12

Бренд: RAPIBREW Страницы: 16

Бренд: Racal Instruments Страницы: 110

Hardon mini R1271C

Бренд: Caen RFID Страницы: 39

Бренд: Everlast Страницы: 30

Бренд: Fagor Страницы: 68

Oxford MAJOR 190

Бренд: Sunrise Medical Страницы: 48

Бренд: Magneti Marelli Страницы: 44

Бренд: Miller Страницы: 44

Бренд: Walkera Страницы: 22

Бренд: DEVI Страницы: 2

Бренд: Westken Страницы: 11

Бренд: human care Страницы: 24

Бренд: Zepro Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды