BendPak HD-14T Скачать руководство пользователя страница 46

Страница: 46 / 76

HD-14T Four Post Lift

P/N 5900037 — Rev. F — February 2022

Filling the Hydraulic Fluid Reservoir

The Hydraulic Fluid Reservoir requires approximately

3.6 gallons

13.5 liters

of Hydraulic Fluid.

The Power Unit will

not

work correctly until it is filled with the approved Hydraulic Fluid.

Approved fluids are any general purpose ISO-32, ISO-46, or ISO-68 Hydraulic Fluid or approved

automatic transmission fluids such as Dexron III, Dexron VI, Mercon V, Mercon LV, or any synthetic
Multi-Vehicle automatic transmission fluid.

⚠

WARNING

Do not run your Power Unit without Hydraulic Fluid; you will damage it.

To fill the Hydraulic Fluid Reservoir

Remove the Reservoir Cap and set it aside.
Take care to

keep contaminants out

of the Hydraulic Fluid Reservoir.

Fill the Hydraulic Fluid Reservoir on the Power Unit with the appropriate amount of Hydraulic Fluid.

When the Reservoir is filled, replace the Reservoir Cap.

Do not connect the Power Unit to a power source at this point

Installing the Flex Tube

To connect the Flex Tube to the Power Unit, you first need to connect the Flex Tube Bracket and the

Flex Tube Angle Bracket.

BendPak recommends orienting the Flex Tube so that the lines coming out of it are near where it
connects on the Power Unit and to the Pushbutton Air Valve.

Содержание HD-14T












































































Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды

BendPak HD-14T, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды