BendPak HD-14T Скачать руководство пользователя страница 41

Страница: 41 / 76

HD-14T Four Post Lift

P/N 5900037 — Rev. F — February 2022

Installing the Return Line

The Return Line takes excess Hydraulic Fluid coming out of the Hydraulic Cylinder and sends it back

into the Fluid Reservoir on the Power Unit.
To install the Return Line, you need the following components:
•

The Return Line

5570795

. The Return Line is a single piece of ¼ inch, black, polyethylene

Tubing and Elbow Compression Fittings on each end. You need to cut off a piece of the supplied

Tubing of the right length to create the Return Line.

•

(2X) COMP to NPT Hydraulic Elbow Fittings

5550089

. The COMP end connects the

Return Line and the NPT end connects to the Power Unit and the Hydraulic Cylinder.

Important

: The Return Line uses the same ¼ inch, black, polyethylene Tubing as the Air Lines. Be

sure not to confuse the two; the Return Line and the Air Lines do completely different
things and

must

be kept separate from each other.

Drawing shows a top view of the Powerside Runway. Not drawn to scale. Not all components shown

Содержание HD-14T












































































Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды

BendPak HD-14T, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды