BendPak HD-14T Скачать руководство пользователя страница 49

Страница: 49 / 76

HD-14T Four Post Lift

P/N 5900037 — Rev. F — February 2022

Connecting the Return Line

One end of the Return Line is already connected to the Hydraulic Cylinder; the other end of the Return

Line needs to be connected to the Power Unit.

To attach the Return Line to the Power Unit

Remove the Shipping Plug from the Hydraulic Return Port on the Power Unit, then attach a

04 COMP – 06 NPT Elbow Compression Fitting (

5550089

) to the Port.

Use Thread Sealant on NPT Threads only

See

Connecting the Power Source

for the possible connector locations.

Attach the Return Line (coming out of the Flex Tube) to the other end of the Fitting.
For information about connection compression fittings, refer to

Working with Compression

Fittings and Tubing

NOTICE

Make sure you are attaching the Return Line to the Power Unit and not the Air Line.

Do not attach the Air Line to the Power Unit by mistake

Connecting the Hydraulic Hose

One end of the Hydraulic Hose is already connected to the Hydraulic Cylinder; the other end of the

Hydraulic Hose needs to be connected to the Power Unit.

To connect the Hydraulic Hose to the Power Unit

Locate the Hydraulic Power Port on the Power Unit you want to use and remove the Shipping

Plug, then attach a 04 JIC – 06L ORB Hydraulic Fitting (

5550008

) to the Port.

See

Connecting the Power Source

for the possible connector locations.

Connect and securely tighten the ORB end of the Fitting to the Hydraulic Power Out on the Power

Unit.

Connect and securely tighten the JIC end of the Fitting to the Hydraulic Hose.

Содержание HD-14T












































































Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды

BendPak HD-14T, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды