BendPak HD-14T Скачать руководство пользователя страница 50

Страница: 50 / 76

HD-14T Four Post Lift

P/N 5900037 — Rev. F — February 2022

Connecting the Power Source

The standard Power Unit for your Lift is 220 VAC, 60 Hz, single phase. The Power Unit must be

connected to an appropriate power source.
Refer to

Wiring Diagrams

for wiring information.

⚠

DANGER

All wiring

must

be performed by a licensed, certified Electrician in accordance with

local and national electrical codes. Do not perform any maintenance or installation

on the Lift without first making sure that main electrical power has been
disconnected from the Lift and

cannot

be re-energized until all procedures are

complete. If your organization has Lockout/Tagout policies, make sure to
implement them after connecting to a power source.

Important electrical information:
•

Improper electrical installation can damage the motor; this is not covered under warranty.

•

Use a separate circuit breaker for each Power Unit.

•

Protect each circuit with a time delay fuse or circuit breaker:
-

For a 208 to 230 VAC, single phase circuit, use a 25 amp fuse.

For a 208 to 230 VAC, three phase circuit, use a 20 amp fuse.

For a 380 to 440 VAC, three phase circuit, use a 15 amp fuse.

The Hydraulic Power Ports are usually labeled

P1/P2

on the Power Unit; the Hydraulic Return Ports

are commonly labeled

T1/T2

CV1/CV2

The following drawing shows the standard configuration for the Power Unit.

Not drawn to scale. Not all components shown.

Содержание HD-14T












































































Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды

BendPak HD-14T, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды