BendPak HD-14T Скачать руководство пользователя страница 22

Страница: 22 / 76

HD-14T Four Post Lift

P/N 5900037 — Rev. F — February 2022

Installing the Crosstubes

Your Lift has two Crosstubes:
•

Crosstube with Large Windows

: Goes on the end of the Lift

opposite

of the Power Post, with

the Windows facing to the inside of the Lift.

5215595

•

Crosstube with Small Windows

: Adjacent to the Power Post, with the Windows facing to the

inside of Lift.

5215596.

Important

: It is possible to install the Crosstubes

incorrectly

in several different ways. Take your

time now and get it right the first time.

The following drawing shows the correct locations for the Crosstubes.

To install the Crosstubes

Orient the Crosstubes in their required locations.

Put the black Slide Blocks (

5716005

) into place on the outside ends of each Gusset, four Slide

Blocks per each Crosstube Gusset.
Align the holes in the Slide Blocks with the rods on the side of the Gusset, then press the Slide
Blocks in. Make sure the Slide Blocks are oriented so that they create a Slot when pushed in.

Top View. Drawing shows how to properly
install two install Slide Blocks onto the
Crosstube Gusset.
Not all components are shown.

Содержание HD-14T












































































Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды

BendPak HD-14T, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды