BendPak HD-14T Скачать руководство пользователя страница 31

Страница: 31 / 76

HD-14T Four Post Lift

P/N 5900037 — Rev. F — February 2022

Bolt both Runways into place, two Hex Head Bolts on each end of the Runways.

Drawing shows how to

secure the Runways to the

Crosstubes.

Two Bolts on each end of the

Runway.

Not all components shown

Important

: The Offside Runway

must

be bolted on both ends when using Rolling Jack.

Make sure that the Primary Locks are engaged.

⚠

WARNING

Do not continue with the installation until you have visually confirmed that all four
Safety Locks are engaged. If they are not engaged, the Runways could move or

fall, possibly causing personal injury or product damage.

Before routing the Cables, extend the Piston on the Hydraulic Cylinder.

To extend the Piston

Remove the Shipping Plug from the Return Line Connector. The Return Line Connector is on the

Cylinder end closest to where the Power Unit will be.

Attach an air pressure source to the Return Line Connector.

Use the air pressure to extend the Hydraulic Cylinder’s Piston and Retainer Plate.

Do not exceed

50 psi

Содержание HD-14T












































































Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды

BendPak HD-14T, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-14T

Отзывы:

Похожие инструкции для HD-14T

Бренды по названию

Популярные бренды