background image

 

­

English

Site~Rite* IV Ultrasound System Operator’s Manual

Chapter 7: Site~Rite* IV Battery Charger

7.3    Charge~Rite™ Battery Charger

The Charge~Rite Battery Charger is used to charge Site~Rite IV Battery Packs. The Charge~Rite 
Battery Charger plugs into a standard power outlet and automatically adjusts to run on any line voltage 
between 90 - 264 VAC, 47 - 63 Hz. The Charge~Rite Battery Charger is shipped with country-specific 
wall plugs. Be sure that the Charge~Rite Battery Charger has the appropriate plug for your country’s 
electrical system.

Charge~Rite fuses are located next to the power switch on the back of the unit. Use only F250 V/3.0A 
fuses in the unit.

Warning: 

Use only the Charge~Rite Battery Charger or Site~Rite Mini Battery Charger to charge 
Site~Rite IV Battery Packs. Use of any other charger to charge Site~Rite IV Battery Packs 
may damage the battery packs and will void your warranty. Never connect a Site~Rite IV 
A/C Adapter to a Charge~Rite Battery Charger or Site~Rite Mini Battery Charger.

7.4  Indicator Lights

The following table lists and describes the indicator light features:

4

3

2

1

Feature

Power

1

Description

Charge~Rite Battery Charger is powered on.

Fast Charge

2

Battery is charging in Fast Charge mode.

Slow Charge

3

Battery is charging in Slow Charge or Maintenance mode.

Battery is either too hot or too cold to charge.
If Temperature Fault and Power indicators illuminate—the 
battery is too hot. Turn the Charge~Rite Battery Charger off and 
wait several minutes for the battery to cool down. 
If Temperature Fault and Slow Charge indicators illumi-
nate
—the battery is too cold. The Charge~Rite Battery Charger 
charges the battery in Slow Charge mode until the battery is 
warmed up.
When the battery is at normal temperature, the Temperature 
Fault and Slow Charge lights turn off and the Charge~Rite 
Battery Charger automatically switches to the Fast Charge mode, 
illuminating the Fast Charge light. Charging continues normally.

Temperature Fault

4

Содержание Site-Rite IV





































Отзывы: