Baker Hughes Consolidated 2900 series Скачать руководство пользователя страница 73

Страница: 73 / 100

XXI. Troubleshooting

Table 17: Troubleshooting 2900 Series POSRV’s

Problem

Possible Cause

Corrective Action

Blowdown incorrect

A. Incorrect Adjuster Assembly setting

Re-set Adjuster Assembly (See Pilot Valve
Setting)

Leakage around fit-

tings

Fittings are not tightened or are
cross threaded.

A. Re-install fittings correctly

Did not install Teflon tape or pipe
sealant.

Re-install fittings with Teflon tape or pipe
sealant.

Leakage under the

Cover Plate when

valve is open.

Guide or Cover Plate Gasket/O-ring
is damaged.

Disassemble valve and replace Cover
Plate Gasket/O-ring.

Cap Screws or Stud Nuts on Cover
Plate are loose.

B. Tighten as required.

Main Valve leaks

through

the Seat

A. Damaged Seat O-Ring

Disassemble valve and replace Seat O-
Ring.

B. Damaged Metal Seat

Disassemble valve and lap Metal Disc
and/or Nozzle.

Metal Seat is not lapped in properly
to Disc Holder

Disassemble Disc and Disc Holder to lap
two together properly

D. Seat too wide

D. Recheck Tables 3 and 4

Main Valve leaks un-

der the Nozzle Seat

A. Damaged Nozzle O-Ring

Disassemble Main Valve and replace dam-
aged Nozzle O-Ring.

Pilot Valve is not open-
ing at set pressure and

Main Valve will not

open

A. Wrong set pressure

A. Readjust the set pressure of the valve.

Main Valve does not

close upon start up.

P2 chamber does not

load with system pres-

sure.

Start-up procedures pressurize the
valve too rapidly.

A. Slowly increase the inlet pressure.

Sensing Tube is installed upside
down.

B. Re-install Sensing Tube correctly.

C. Closed Filter

C. Clear or replace Filter.

Main Valve Piston is not resting

on nozzle.

Push the Main Valve Piston down to
nozzle through the compression fitting on
top of the Cover Plate.

Leakage through the

Pilot Valve

A. Operating pressure too high

A. Adjust operating pressure

B. O-Ring or Spring Seal degradation

Disassemble and replace O-Ring or Spring
Seals

Main Valve opens and

allows the discharge

media to flow back

into the pressure

vessel

Back pressure is greater than set
pressure and forces the Main Disc
up, and the media flows backward
into the vessel.

A. Install Backflow Preventer

Discharging into a closed container
or not enough capacity in the dis-
charge system.

B. Install Backflow Preventer.

Consolidated 2900 Series POSRV Maintenance Manual

Содержание Consolidated 2900 series





































































































Результаты поиска

Содержание Consolidated 2900 series

Отзывы:

Похожие инструкции для Consolidated 2900 series

Бренды по названию

Популярные бренды

Baker Hughes Consolidated 2900 series, Руководство по обслуживанию

Результаты поиска

Содержание Consolidated 2900 series

Отзывы:

Похожие инструкции для Consolidated 2900 series

Бренды по названию

Популярные бренды