Baker Hughes Consolidated 2900 series Скачать руководство пользователя страница 29

Страница: 29 / 100

A. Removal of Pilot Valve from

Main Valve

1. Make sure there is no media pressure in the

vessel, in the valve inlet, in the main valve,

or in the pilot valve.

2. Disconnect the Sensing Tube, Dome Tube and

Discharge Line from the Pilot Valve.

3. All other external attachments should be

removed to free the Pilot Valve for Disassembly.

4. Loosen and remove the two cap bolts holding

the pilot valve to the mounting bracket.

5. Place parts in the order they are disassembled

to facilitate reassembly.

B. Disassembly of Main Valve

Note: If the pilot valve has not been removed,

then refer to Section XIII.A.

1. If applicable, remove sensing tube fitting from

Sensing Tube

2. Remove and discard Plug Filter from Sensing

Tube (if applicable).

3. Loosen and remove the Stud Nuts on the

Cover Plate.

4. Remove the Bracket.

5. Install 1/4” MNPT pipe plug into Cover Plate

where dome line is installed. Pipe plug will

prevent Main Valve Piston from falling out of

Cover Plate when the assembly is removed.

6. Remove Cover Plate and Main Valve Piston

assembly from Base.

ATTENTION!

If Main Valve Piston O-Ring or Spring Energize

Seal is damaged, then Main Valve Piston may

fall out of Cover Plate during disassembly.

7. Remove pipe plug from Cover Plate.

8. Remove the Main Valve Piston from the Cover Plate

using a dowel pressed through the center hole in
the top of the Cover Plate.

XIII. Disassembly of the 2900 POSRV

Wear necessary

protective

equipment to

prevent possible

injury

Lower pressure

and stand clear of

discharge when

working on valve to

avoid severe personal

injury or death.

Do not remove

bolts if pressure

in line, as this will

result in severe

personal injury or

death

Know all valve

exhaust/leakage

points to avoid

possible severe

personal injury or

death

Consolidated 2900 Series POSRV Maintenance Manual

Содержание Consolidated 2900 series





































































































Результаты поиска

Содержание Consolidated 2900 series

Отзывы:

Похожие инструкции для Consolidated 2900 series

Бренды по названию

Популярные бренды

Baker Hughes Consolidated 2900 series, Руководство по обслуживанию

Результаты поиска

Содержание Consolidated 2900 series

Отзывы:

Похожие инструкции для Consolidated 2900 series

Бренды по названию

Популярные бренды