Baker Hughes Consolidated 2900 series Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 100

background image

A. General Information

1. Before putting the reconditioned valve in service,

it must be set to open at the required set pressure.
Although the valve can be set on the service
installation, it is more convenient to set the valve

and check seat tightness on a test stand.

2. Test Equipment:

The test stand used for testing POSRVs normally
consists of a pressure source supply line with

a throttle valve and receiver that have the

following features:
a.  Outlet for attaching the valve to be tested
b.  Pressure gauge with a shutoff valve
c.  Drain line with a shutoff valve
d.  Adequate receiver volume for the valve to

be tested and to achieve proper operation

3. Test Media:

For best results, valves shall be tested by type,

as follows:

a. Steam valves are tested on saturated steam.
b. Air or gas valves are tested on air or gas at

ambient temperature.

c. Liquid valves are tested on water at ambient

temperature.

B. With Standard Options

Note: Seal all pipe threads with a non-organic sealant

or Teflon

®

tape.

B.1 39PV07/37

1. Attach pilot to main valve using two Socket Head

Cap Screws (Bracket).

2. Install the 3/8” O.D. tubes (Refer to Table 13 for

sizing of tubing) into the fittings for the inlet and
dome ports. Make sure the tube ends are fully
inserted before torquing. Begin torquing the fitting,
about midway down; verify that Swagelok Gap
Inspection Gauge (Swagelok P/N MS-IG-468) will go.

Continue to torque down fitting until Swagelok Gap
Inspection Gauge will not go. After torquing, remove
to assure the ferrule is in good contact with the
tubing. Refer to Table 14 and Figure 53 to determine
if ferrule has seated itself properly. Reinstall the
tubing.

Table 13: Ferrule Wall Thickness

Pressure Class

Wall Thickness (min.)

in.

mm

150# to 900#

.035

0.89

1500#

.049

1.24

2500#

.065

1.65

Table 14: Tubing Dimensions

Tubing Diameter

Tubing Length (A)

in.

mm

in.

mm

.250

6.35

.190

4.83

.375

9.53

.250

6.35

.500

12.70

.340

8.64

3. The vent port of the pilot valve is vented to

atmosphere in standard configuration.

4. Final standard configuration for a 39PV07 or

39PV37 without any options is shown in Figure 54.

XX. Setting and Testing

A

Figure 53: Tubing Dimensions

Figure 54: 39PV07/37

68 | BHGE

© 2018 Baker Hughes, a GE company. All Rights Reserved.

«
...
66
67
68
69
70
...
»

Содержание Consolidated 2900 series





































































































Отзывы:

Нет отзывов

Похожие инструкции для Consolidated 2900 series

Бренд: Calsense Страницы: 74

SIGMA CONTROL 2

Бренд: KAESER KOMPRESSOREN Страницы: 246

Бренд: Olsberg Страницы: 68

Бренд: York Страницы: 20

Бренд: Parkside Страницы: 65

Бренд: Talgil Страницы: 14

Бренд: Tadao Страницы: 2

Бренд: Dejero Страницы: 24

Бренд: WINDY NATION Страницы: 16

Бренд: Kaba Mauer Страницы: 10

Бренд: HEIDENHAIN Страницы: 257

SaunaLogic SL2 Control

Бренд: Finnleo Страницы: 14

Бренд: ACTi Страницы: 20

Бренд: SOARNEX Страницы: 14

Бренд: Tristan Auron Страницы: 30

Бренд: Eaton Страницы: 108

Бренд: Carrier Страницы: 4

Бренд: Maker Factory Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды