Baker Hughes Consolidated 2900 series Скачать руководство пользователя страница 62

Страница: 62 / 100

Note: Do not install adjuster assembly into Pilot Base

with O-Rings installed without wrench tightening
Adjuster Top to Adjuster Bottom together.
Adjuster Top can get stuck in Pilot Base if the
Adjuster Top is not tighten properly.

e. Install O-Ring (Adjuster Top) into groove on

Adjuster Top.

f. Install O-Ring (Adjuster Bottom) into groove

on Adjuster Bottom. Install from the opposite

end of the square wrenching flats.

g. Lightly lubricate both external O-Rings on

Adjuster Assembly. Install Adjuster Assembly

into Pilot Base with the Adjuster Top going

in first. Rotate the assembly clockwise during
installation until the threads are engaged. This
helps the O-Rings get by chamfers and holes.

h. Continue to turn Adjuster Assembly clockwise

into Pilot Base until it stops.

i. Turn Adjuster Assembly counterclockwise

the number of flats that was recorded in
Disassembly Instructions (Section XVII.A),

step 16.

j. Thread the Adjuster Lock Nut clockwise onto

the Adjuster Assembly hand tight.

k. Thread Adjuster Cap clockwise onto Adjuster

Assembly hand tight.

Note: Make sure Adjuster Cap and Adjuster Lock

Nut threads freely on Adjuster Bottom. Adjuster
Assembly may be inadvertently rotated if these
two parts do not fit loosely.

3. The Insert Assembly of the pilot consists of:

1 – Insert Top

1 – Insert Bottom

1 – Spring Seal (Insert)

1 – O-Ring (Insert)

a. Press Spring Seal (Insert) into groove on

the Insert Bottom. Make sure spring is

facing upwards.

b. Install Insert Top over Insert Bottom with the

spring seal side going in first.

c. Lightly lubricate O-Ring groove now formed

by the two insert parts. This lubrication is

used to hold the O-Ring in place when it

is being inserted into Pilot Base.

d. Place O-Ring (Insert) into groove.
e. Final Insert Assembly is shown in Figure 49.

f. Turn Insert Assembly over and thread into

Pilot Base with T-handle groove wrench

(Part #4995401 Figure 81). Tighten wrench tight.
Make sure milled slot is facing up.

g. Lubricate Main Piston stem and cycle Main

Piston through Spring Seal (Insert) five times.

Note: For Dirty Service Option, please refer to

assembly instructions included in the Dirty
Service Option section (Section XXII.B.4).

4. Install O-Ring (Top Plate) into groove on top of

Pilot Base.

Note: For Dirty Service Option, O-Ring (Top Plate) is

installed into groove on top of the Dirty Service
Insert.

a. Lubricate the Spring Seal (Main Piston) and

Top Plate gland. Install the Spring Seal (Main
Piston) into Top Plate. The spring should be
oriented as shown in Figures 50 or 51.

b. Lubricate Main Piston before installing. Install

the Main Piston into the Top Plate with the

Spring Washer bearing point going in first.

Be careful not to damage the Spring Seal

(Main Piston).

Spring Seal

Insert Bottom

O-Ring (Insert)

Insert Top

Figure 49: Insert Assembly

Spring Seal

(Main Piston)

Top Plate

Figure 50: Top Plate (39PV07)

XIX. Reassembly of Pilot Valve (Contd.)

62 | BHGE

Содержание Consolidated 2900 series





































































































Результаты поиска

Содержание Consolidated 2900 series

Отзывы:

Похожие инструкции для Consolidated 2900 series

Бренды по названию

Популярные бренды

Baker Hughes Consolidated 2900 series, Руководство по обслуживанию

Результаты поиска

Содержание Consolidated 2900 series

Отзывы:

Похожие инструкции для Consolidated 2900 series

Бренды по названию

Популярные бренды