AVANT A37190 Скачать руководство пользователя

Страница: 56 / 66

56 (66)

7.11.1

Using the wire rope brush

WARNING

Hazard of thrown objects - Keep bystanders away.

Note that the broom may eject

sand, stones, pieces of wood or other material far from the broom. Stop using the broom,
if there are others closer than 5 meters from the broom.

Adjust the rotating speed of the broom according to operating conditions, keeping it within the limits shown on

page

12. Slow to moderate loader engine RPM level is usually enough to rotate the broom adequately so that

the broom sweeps the material neatly to its side. On 600- and 700-series loaders one or two working hydraulic

pumps may be used according to operating conditions. High rotating speed will wear down the brush more

quickly and usually it is not necessary to use high rotating speeds.

In order to prevent the brush from getting damaged or worn unevenly, do not use the
broom for pushing purposes, without rotating it simultaneously.

Содержание A37190



































































Результаты поиска

Содержание A37190

Отзывы:

Похожие инструкции для A37190

Бренды по названию

Популярные бренды

AVANT A37190, Руководство оператора

Результаты поиска

Содержание A37190

Отзывы:

Похожие инструкции для A37190

Бренды по названию

Популярные бренды