Automationdirect.com DL06 Скачать руководство пользователя страница 320

Страница: 320 / 533

DL06 Micro PLC User Manual, 3rd Edition, Rev. E

5-159

Chapter 5: Standard RLL Instructions

1
2
3
4
5
6
7
8
9

10
11
12
13
14

The instruction will be executed once per scan, provided the input remains on. The function

parameters are loaded into the first level of the accumulator stack and the accumulator by two

additional instructions. Listed below are the steps necessary to program the Remove From

Table function.

Step 1: Load the length of the table (number of V-memory locations) into the first level

of the accumulator stack. This parameter must be a HEX value, 0 to FF.

Step 2: Load the starting V-memory location for the table into the accumulator.

(Remember, the starting location of the table is used as the table length

counter.) This parameter must be a HEX value.

Step 3: Insert the RFT instructions which specifies destination V-memory location

(Vaaa). This is where the value will be moved to.

Helpful Hint:

— For parameters that require HEX values when referencing memory locations,

the LDA instruction can be used to convert an octal address to the HEX equivalent and load

the value into the accumulator.

Helpful Hint:

— The instruction will be executed every scan if the input logic is on. If you do

not want the instruction to execute for more than one scan, a one-shot (PD) should be used

in the input logic.

Helpful Hint:

— The table counter value should be set to indicate the starting point for the

operation. Also, it must be set to a value that is within the length of the table. For example, if

the table is 6 words long, then the allowable range of values that could be in the table counter

should be between 1 and 6. If the value is outside of this range or zero, the data will not be

moved from the table. Also, a one-shot (PD) should be used so the value will only be set in one

scan and will not affect the instruction operation.

NOTE: Status flags (SPs) are only valid until another instruction that uses the same flag is executed,

or the end of the scan The pointer for this instruction can be set to start anywhere in the table. It is not

set automatically. You must load a value into the pointer somewhere in your program.

aaa

R F T

Operand Data Type

DL06 Range

aaa

V-memory

See memory map

Discrete Bit Flags

Description

SP56

On when the table pointer equals zero.

Used

HPP Used

Remove from Table (RFT)

The Remove From Table instruction pops a value off a table

and stores it in a V-memory location. When a value is removed

from the table all other values are shifted up 1 location. The first

V-memory location in the table contains the table length counter.

The table counter decrements by 1 each time the instruction is

executed. If the length counter is zero or greater than the maximum

table length (specified in the first level of the accumulator stack) the

instruction will not execute and SP56 will be On.

Содержание DL06






















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DL06

Отзывы:

Похожие инструкции для DL06

Бренды по названию

Популярные бренды

Automationdirect.com DL06, Руководство пользователя

Результаты поиска

Содержание DL06

Отзывы:

Похожие инструкции для DL06

Бренды по названию

Популярные бренды