Automationdirect.com DL06 Скачать руководство пользователя страница 311

Страница: 311 / 533

DL06 Micro PLC User Manual, 3rd Edition, Rev. E

5-150

Chapter 5: Standard RLL Instructions

1
2
3
4
5
6
7
8
9

10
11
12
13
14

Listed below are the steps necessary to program the Table To Destination function.

Step 1: Load the length of the data table (number of V-memory locations) into the first

level of the accumulator stack. This parameter must be a HEX value, 0 to FF.

Step 2: Load the starting V-memory location for the table into the accumulator.

(Remember, the starting location of the table is used as the table pointer.) This

parameter must be a HEX value.

Step 3: Insert the TTD instruction which specifies destination V-memory location

(Vaaa).

Helpful Hint:

— For parameters that require HEX values when referencing memory locations,

the LDA instruction can be used to convert an octal address to the HEX equivalent and load

the value into the accumulator.

Helpful Hint:

— The instruction will be executed every scan if the input logic is on. If you do

not want the instruction to execute for more than one scan, a one-shot (PD) should be used in

the input logic.

Helpful Hint:

— The pointer location should be set to the value where the table operation will

begin. The special relay SP0 or a one-shot (PD) should be used so the value will only be set in

one scan and will not affect the instruction operation.

NOTE: Status flags (SPs) are only valid until another instruction that uses the same flag is executed,

or the end of the scan. The pointer for this instruction starts at 0 and resets when the table length

is reached. At first glance it may appear that the pointer should reset to 0. However, it resets to 1,

not 0.

T T D

aaa

T T D

aaa

Operand Data Type

DL06 Range

aaa

V-memory

See memory map

Discrete Bit Flags

Description

SP56

On when the table pointer equals the table length.

Used

HPP Used

Table to Destination (TTD)

The Table To Destination instruction moves a value from a

V-memory table to a V-memory location and increments the

table pointer by 1. The first V-memory location in the table

contains the table pointer which indicates the next location in the

table to be moved. The instruction will be executed once per scan

provided the input remains on. The table pointer will reset to 1

when the value equals the last location in the table. The function

parameters are loaded into the first level of the accumulator stack

and the accumulator by two additional instructions.

Содержание DL06






















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DL06

Отзывы:

Похожие инструкции для DL06

Бренды по названию

Популярные бренды

Automationdirect.com DL06, Руководство пользователя

Результаты поиска

Содержание DL06

Отзывы:

Похожие инструкции для DL06

Бренды по названию

Популярные бренды